User manual HANNA INSTRUMENTS PRIMO SERIES BROCHURE

[. . . ] Instruction Manual Primo Series Dear Customer, Thank you for choosing a Hanna product. Please read carefully this instruction manual before using the meter. If you need additional technical information, do not hesitate to e-mail us at tech@hannainst. com. [. . . ] If the repair is not covered by the warranty, you will be notified of the charges incurred. If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization number from the Customer Service department and then send it with shipping costs prepaid. When shipping any instrument, make sure it is properly packaged for complete protection. ACCESSORIES HI 70031P HI 70032P HI 70039P HI 7031L HI 7032L HI 7039L 1413 µS/cm solution, 20 mL sachet, 25 pcs 1382 ppm solution, 20 mL sachet, 25 pcs 5. 00 mS/cm solution, 20 mL sachet, 25 pcs 1413 µS/cm solution, 500 mL bottle 1382 ppm solution, 500 mL bottle 5. 00 mS/cm solution, 500 mL bottle Hanna Instruments reserves the right to modify the design, construction and appearance of its products without advance notice. ISTPRIMOR1 05/05 SPECIFICATIONS OPERATION ERROR CODES Error in calibration, wrong calibration solution or damaged probe. Low battery indication. Primo, Primo 2, Primo 5 Range Primo Primo 2 Primo 5 Resolution Primo Primo 2 Primo 5 1999 ppm (mg/L) 1999 ppm (mg/L) / 0. 0 to 60°C 1999 µS/cm 1 ppm (mg/L) 1 ppm (mg/L) / 0. 1°C 1 µS/cm Primo 1, Primo 3, Primo 4 Range Primo 1 Primo 3 Primo 4 Resolution Primo 1 Primo 3 Primo 4 1999 ppm (mg/L) 1999 ppm (mg/L) / 0. 0 to 60°C 10. 00 mS/cm 1 ppm (mg/L) 1 ppm (mg/L) / 0. 1°C 0. 01 mS/cm · Turn the meter on by pressing the ON/OFF button. · Immerse the probe in the sample to be measured, without exceeding the maximum immersion level. · Stir gently and wait for stable reading. The meter automatically compensates for temperature variations. · To extend the batteries life, after 5 minutes of non-use the meter provides for auto-off. CALIBRATION · Switch the meter on. · Press and hold the ON/OFF button for about 3 seconds. The required calibration solution value will start blinking on the display to indicate that the calibration mode has been entered. "1382" for Primo, Primo 1, Primo2, Primo3 "5. 00" for Primo 4, and "1413" for Primo 5 · Immerse the probe in the proper calibration solution without exceeding the maximum immersion level. · Stir gently and wait for about 20 seconds. · Once the display stops blinking, the meter is calibrated and ready for use. CE DECLARATION OF CONFORMITY Accuracy (@20°C/68°F) Primo ±2 % F. S. / ±0. 5°C Primo 5 ±2 % F. S. Calibration solution Primo Primo 2 Primo 5 Calibration Primo Primo 2 Primo 5 HI 70032 (1382 ppm) HI 70032 (1382 ppm) HI 70031 (1413 µS/cm) Automatic, at 1382 ppm Automatic, at 1382 ppm Automatic, at 1413 µS/cm Accuracy (@20°C/68°F) Primo 1 ±2 % F. S. / ±0. 5°C Primo 4 ±2 % F. S. [. . . ] Any variation introduced by the user to the supplied equipment may degrade the instrument EMC performance. To avoid electrical shocks, do not use this instrument when voltage at the measurement surface exceeds 24Vac or 60Vdc. To avoid damage or burns, do not perform any measurement in microwave ovens. [. . . ]