User manual HARMAN KARDON AVR 154

[. . . ] AVR 154 AUDIO/VIDEO RECEIVER OWNER'S MANUAL SAFETY INFORMATION Important Safety Instructions 1. The A/V receiver's cabinet may be cleaned by gently wiping with a soft cotton or microfiber cloth. Do not use water or any liquid cleaners. Do not block any of the ventilation openings. [. . . ] NOTE: The Speaker/Channel Indicators on the front panel of the receiver (see Figure 44) display the speaker size settings as follows. For each speaker configured as SMALL, a single box appears in its position. For each speaker configured as LARGE, a double box appears in its position. If a speaker is configured as NONE, no box appears. The subwoofer is indicated by a single box, or no box if no subwoofer has been configured. The letters inside the boxes appear when a digital signal is being received with that channel discretely encoded. The letters flash when the signal is not present, such as when a DVD is paused. · L/R+LFE: This setting sends all low-frequency information to the subwoofer, including both information that would normally be played through the front left and right speakers and the special low-frequency effects (LFE) channel information. · LFE: This setting steers low-frequency information contained in the left and right program channels to the front speakers, and directs only the LFE channel information to the subwoofer. · NONE: This setting steers all low-frequency information to the front speakers, and no information to the subwoofer output. Use this setting with full-range front speakers, or with a passive or a powered subwoofer connected to the front speaker outputs. NOTE: If you are using a Harman Kardon HKTS speaker system, select the SMALL setting for the LEFT/RIGHT, CENTER and SURROUND lines, and the subwoofer will automatically be set to SUB. Speaker Crossover Menu On the Manual Setup menu, move the cursor to the SPEAKER X-OVER line and press the OK Button to display the Speaker Crossover menu. See Figure 45. Figure 45 ­ Speaker Crossover Menu Screen 30 INITIAL SETUP Setting the Speaker Crossover menu correctly ensures that your speakers sound their best. Although you could skip this step the first time you use the receiver, we recommend that you take the few extra minutes to enter the correct crossover settings. Select from seven possible settings: 40Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. For each speaker group, select the number that matches or is just above the low end of your speaker's frequency response, which you recorded in Step One ­ Determine Speaker Size. Record the speaker crossover settings in Table A6 in the Appendix. The LFE line sets the frequency that determines what information is sent to the subwoofer. The subwoofer output combines low-frequency information for all channels. To make sure no information is lost, set the LFE line to the speaker group with the highest crossover frequency. Move the cursor to the LFE line, and use the < / > Buttons to make a selection. If all three speaker groups have the same setting, leave the LFE filter at its factory default of LEFT/RIGHT. Move the cursor to the BACK TO MANUAL SETUP line and press the OK Button to return to the Manual Setup menu. [. . . ] Search Play (DVD) Play (DVD) Play (DVD) Play Skip ­ (DVD) Skip + (DVD) Skip ­ (DVD) Skip + (DVD) Skip ­ (DVD) Skip + (DVD) Macro 1 Macro 2 Macro 3 Macro 4 Macro 1 Macro 2 Macro 3 Macro 4 Macro 1 Macro 2 Macro 3 Macro 4 Macro 1 Macro 2 Macro 3 Macro 4 Disc Skip Skip DVD CD/CD-R Tape VCR (VID1) TiVo (VID1) DMC (VID1/ CBL (VID2) HDMI 1/2/3) Source (DMC250 only) PPV Angle Clear Clear Clear FAV Bypass Music SAT (VID2) TV (VID3) HDMI 1/2/3 Audio or Playlist Time Next Chapter Angle Clear Slow Forward Prev Chapter Track Direct Random Play Clear +10 Track Increment Cancel Cancel FAV Next Alt Sleep Angle/FAV V-off Play Mode 57 Dolby Surround Dolby Modes 58 DTS Surround DTS Digital Modes 59 DTS Neo:6 60 Night 61 Logic 7 62 Stereo 63 Skip Down 64 Skip Up 65 Dim 66 Rewind (<< ) 67 Play (<>) 68 F F (>>) 69 Record 70 Stop 71 Pause DTS Neo:6 Select Night Mode Select Logic 7 Select Stereo Mode Select Skip ­ (DVD) Skip + (DVD) Dimmer R. Search Note: When any of the transport controls are pressed while the remote is in AVR, Video 2 or Video 3 mode, the remote will automatically switch to DVD mode and the command will be applied to the DVD player. If you then press a button native to the original mode, e. g. , Volume Down for the AVR, the remote will revert to the original mode. See Punch-Through Programming, described in the Advanced Functions section, for more information. 52 52 APPENDIX Refer to Tables A10 through A16 when programming the codes for your components into the remote. [. . . ]