User manual HARMAN KARDON AVR 335

[. . . ] ® Power for the Digital Revolution. ® AVR 335 AUDIO/VIDEO RECEIVER OWNER'S MANUAL AVR 335 AUDIO/VIDEO RECEIVER 3 4 4 5 7 10 13 14 16 16 16 17 18 20 22 24 25 27 27 27 27 28 28 29 31 32 32 33 33 33 33 33 34 34 35 35 35 35 37 37 37 37 37 37 38 39 39 39 39 40 41 43 53 53 54 55 Introduction Safety Information Unpacking Front-Panel Controls Rear-Panel Connections Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System Configuration Speaker Placement System Setup Input Setup Surround Setup Automated Speaker Setup Using EzSet+ Speaker Setup Delay Settings Output Level Adjustment Operation Basic Operation Source Selection Volume Control Surround Mode Selection Digital Audio Playback Surround Mode Chart Tuner Operation Recording Output Level Trim Adjustment Advanced Features Front-Panel Display Fade Display Brightness Turn-On Volume Level Semi-OSD Settings Full-OSD Time-Out Adjustment Default Surround Mode Multiroom Operation Multiroom Setup Surround Amplifier Channel Assignment Multiroom Operation Programming the Remote Programming the Device Codes Direct Code Entry Auto Search Method Code Readout Macro Programming Programmed Device Functions Volume Punch-Through Channel Control Punch-Through Transport Control Punch-Through Reassigning the VID4 Device Control Selector Resetting the Remote Memory Function List Setup Code Tables Troubleshooting Guide Processor Reset Technical Specifications Index Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on-screen or on the front-panel information display 1 ­ (number in a square) indicates a specific front-panel control ¡ ­ (number in a circle) indicates a rear-panel connection a ­ (number in an oval) indicates a button or indicator on the remote å ­ (letter in an oval) indicates a button on the Zone II remote See trademark acknowledgements on page 54. INTRODUCTION Thank you for choosing Harman Kardon®!With the purchase of a Harman Kardon AVR 335, you are about to begin many years of listening enjoyment. Designed to provide all the excitement and detail of movie soundtracks and every nuance of musical selections, the AVR 335 harnesses advanced technologies usually found only in higher-priced receivers. [. . . ] Press the </> Buttons o to select the option that best describes the speakers in use at the left and right back surround positions based on the definitions on this page: When NONE is selected, the system will adjust so that only 5. 1-channel surround processing/decoding modes are available and the surround back amplifier channels will not be used. When this is the case for your system you may wish to take advantage of the availability of this amplifier channel pair for use in powering a second set of speakers that have their source selected by the AVR 335's multiroom control system. When SMALL is selected, the system will adjust so that the full complement of 6. 1/7. 1 surround processing/ decoding modes are available, and low-frequency information below the crossover point will be sent to the subwoofer output. If you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the surround back channel. When LARGE is selected, the system will adjust so that all 6. 1/7. 1 surround processing/decoding modes are available, and a full-range signal will be sent to the surround back channels, with no low-frequency information sent to the subwoofer output. When you have completed your selection for the back surround channels, press the ¤ Button n to move the cursor to SUBWOOFER. Press the < / > Buttons o on the remote to select the option that best describes your system. The choices available for the subwoofer position will depend on the settings for the other speakers, particularly the front left/right positions. If the front left/right speakers are set to SMALL, the subwoofer will automatically be set to SUB, which is the "on" position. If the front left/right speakers are set to LARGE, three options are available: · If no subwoofer is connected to the AVR 335, press the < / > Buttons o so that NONE appears in the on-screen menu. When this option is selected, all bass information will be routed to the front left/right "main" speakers. · If a subwoofer is connected to the AVR 335, you have the option to have the front left/right "main" speakers reproduce bass frequencies at all times, and have the subwoofer operate only when the AVR 335 is being used with a digital source that contains a dedicated Low-Frequency Effects, or LFE, soundtrack. This allows you to use both your main and subwoofer speakers to take advantage of the special bass created for certain movies. Press the </ > Buttons o so that SUB (LFE) appears in the on-screen menu. · If a subwoofer is connected and you wish to use it for bass reproduction in conjunction with the main front left/right speakers, regardless of the type of program source or Surround mode you are listening to, press the < / > Buttons o so that SUB LFE+L/R appears in the onscreen menu. When this option is selected, a fullrange signal will be sent to the front left/right "main" speakers, and the subwoofer will receive the bass frequencies under frequency selected, as described below. When all initial speaker "size" settings have been made, you now have the option to take advantage of the AVR 335's Quadruple Crossover system, which allows individual crossover settings to be made for each speaker grouping. The low-frequency crossover point is set by the design of your speakers. Depending on the design and driver complement of your speakers, it is defined as the frequency below which the signal should be redirected to the subwoofer, and is therefore usually the lowest possible frequency the speaker is capable of reproducing. If your main speakers include an onboard powered woofer section intended to serve the function of a subwoofer, the crossover point should be set at the frequency where the loudspeaker divides the signal between its powered woofer section and any other drivers. If you have already run EzSet+ the settings calculated during that procedure will already appear. No further adjustment is required unless you wish to conform a specific item to your personal taste or a nonstandard system configuration. [. . . ] Button Name 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 Tune Up Direct Clear Preset Up Tune Down OSD D. Skip Preset Down M1 M2 M3 M4 Dolby Sur DTS Sur DTS Neo:6 Logic 7 Stereo Skip Down Skip Up Rewind Play Fast Forward Record Stop Pause Stop (DVD) Pause (DVD) Stop Pause AVR Function Tune Up Direct Tuner Entry Clear Preset Tune Up Tune Down OSD Disc Skip (DVD) Preset Tune Down Macro 1 Macro 2 Macro 3 Macro 4 Dolby Mode Select DTS Digital Modes DTS Neo:6 Select Logic 7 Select Stereo Mode Select Skip ­ (DVD) Skip + (DVD) R. Search Record Stop Pause Rewind Fast Fwd Stop Scan ­ Scan + Rewind Fast Fwd Stop Pause R. Play Play Record/Pause Record Stop (DVD) Pause (DVD) Stop (DVD) Pause (DVD) Stop (DVD) Pause (DVD) Skip ­ (DVD) Skip + (DVD) Play (DVD) F. [. . . ]