User manual HARMAN KARDON AVR 70

[. . . ] AVR70 engelsk manual 11/01/98 11:57 Side 1 Harman Kardon AVR70 Audio/VideoReceiver Volume VISUAL SIGNAL EVEL CH TV LD VCR 12 AUX TEST MEMO AUTO TUNED STEREO dB kHz MHz STEREO PRO·LOGIC MOVIE HALL MATRIX 3-LOGIC AUTO MEMO P-SCAN DISP Aux DISP OSD Delay MODE P·SET P·Scan TUNE Mute RDS ar Mode DISP. AF PTY. Bass Treble Balance AUX Min Max Min Max L R VIDEO L­AUDIO­R Owner's Manual AVR70 engelsk manual 11/01/98 11:57 Side 2 Declaration of Conformity We, Harman Kardon Europe A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55 013 EN 55 020 EN 55 022 EN 60 065 EN 60 555-2-3 Steen Michaelsen Harman Kardon Europe A/S Birkerød, DENMARK 11/95 AVR70 engelsk manual 11/01/98 11:57 Side 3 Front Panel 2 AVR70 Volume 1 VISUAL SIGNAL LEVEL CH STEREO TV LD VCR 12 AUX TEST MEMO AUTO TUNED STEREO dB & kHz MHz PRO·LOGIC MOVIE HALL MATRIX 3-LOGIC AUTO MEMO P-SCAN DISP AM/FM CD T-MON T·2 TV LD VCR1 VCR 2 Aux DISP OSD Delay MODE P·SET P·Scan TUNE Mute ^ RDS Power Phones Memo Clear Mode DISP. AF PTY. Bass Treble Balance AUX Min Max Min Max L R VIDEO L­AUDIO­R 3 45 6 * ( 7 89 ÓÔ ) !@ Ù # i $ ^ % ~ ÒÚ Û 1 Information display 2 Remote Sensor Window 3 AM/FM Tuner Mode Selection 4 CD 5 Tape1/ Monitor 6 Tape 2 7 Video Sources 8 Aux 9 Display ) OSD (On Screen Display) !Delay @ Mode # Preset Tuning $ P-Scan % Tune ^ Mute & Volume Control * Power ( Headphone Jack Ó Memo Ô Clear FM Mode Ò RDS Display Ú RDS Alternate Frequency Û RDS Programme Type Ù Bass i Treble ^ Balance ~ Front Panel Inputs Information Display ¡ VISUAL TM£¢ TEST MEMO AUTO TUNED § STEREO dB > SIGNAL LEVEL CH STEREO TV LD VCR 12 AUX kHz MHz PRO·LOGIC MOVIE HALL MATRIX 3-LOGIC AUTO MEMO P-SCAN DISP ¶ · < ¡ "Visual" Indicators TM Test £ Memo ¢ Auto Tuned ¤ / , ª § Stereo ¶ Volume Indication · Tuner Frequency Indication ª Main Information Display , Display / P-Scan ¤ Auto Memo < Mode Statue > Signal Level Indication AVR70 engelsk manual 11/01/98 11:57 Side 4 Rear Panel ­ Audio and System Connections é ANTENNA OUT VCR2 TV MONI CENTER PRE OUT L FRONT R SURR. [. . . ] To clear the memory for a specific individual key location, put the Use/Learn switch in the Learn position. Press the Main Power Off b button and the button to be cleared at the same time. Both the Sending and Learning indicators will light momentarily. When the lights go out, the memory has been cleared of the user programmed code and returned to the factory preset. Return the Use/Learn a switch to the Use position when you are finished. To clear the remote's entire memory and return all keys to their factory preset commands first put the Use/Learn a switch in the Learn position. Then press the Main Power On button b and confirm that the Learning indicator y has illuminated. While continuing to press the Power On button, press and hold the Power Off b button until the Learn indicator goes off for about 3 seconds. This indicates that the memory has been cleared of any user programmed commands and that the original commands have been restored. Slide the Use/Learn switch back to the Use a position to return the remote to normal operation. To program the remote, you need the remote of the device, whose functions shall be programmed. Note that it is not necessary to program all keys, only those that are required to operate the subject device. Keys not programmed will retain the codes preprogrammed at the factory. AVR70 engelsk manual 11/01/98 11:57 Side 14 ENGLISH System Configuration 14 Center Front Speaker When all audio, video and system connections have been made, there are a few configuration adjustments to be made. A few minutes spent to correctly configure and calibrate the unit will greatly add to your listening experience. Speaker Selection and Placement The placement of speakers in a multi channel home theater system can have a noticeable impact on the quality of sound reproduced. The AVR70 will deliver accurate reproduction with any high quality speakers. No matter which type or brand of speakers are used, the same model or brand of speaker should be used for the front left, center and right speakers. This creates a seamless front soundstage, and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mis-matched front channel speakers. For the most accurate and exciting reproduction of bass frequencies a separate subwoofer should be used. Speaker Placement For best imaging, it is recommended that the center channel speaker be placed in line with the left and right speakers. It should be placed above the center of TV monitor or rear screen projector, with the speaker as close to the top of the screen as possible. If possible, adjust the center channel speaker so that it is pointing towards the listening position. Once the center speaker is positioned, adjust the height of the left and right speakers so the tweeter of those speakers is no more than 60 cm off center from the tweeter on the center channel speaker. [. . . ] Movie Surround uses decoding similar to Pro Logic, but it permits delay times up to 90 ms. Use this mode instead of Pro Logic to experiment with surround times above 30 ms, or if the delay time formula suggests a larger time delay for your room. DOLBY 3 STEREO MOVIE SURROUND 10 ms ­ 90 ms Initial Setting = 20 ms HALL SURROUND This mode is designed for use with stereo recordings. It provides a sound field effect that 10 ms ­ 90 ms simulates the complex combination of direct and reflected sounds that create Initial Setting = 20 ms the rich reverberant atmosphere of a medium sized circular concert hall. where the feeling of a wide surround effect is desired. MATRIX SURROUND This mode is designed for use with sports broadcasts, live concerts or other programs STEREO This mode turns off all surround processing and presents the pure left and right channel presentation of two channel stereo programs. 10 ms ­ 90 ms Initial Setting = 20 ms No Surround Channels AVR70 engelsk manual 11/01/98 11:57 Side 27 Troubleshooting 27 ENGLISH Troubleshooting Chart SYMPTOM No front panel lights when power switch is pressed Display lights, but no sound or picture CAUSE · No AC Power SOLUTION · Make certain AC power cord is plugged into a live outlet. [. . . ]