User manual HARMAN KARDON AVR100

[. . . ] 250 Crossways Park Drive, Woodbury, New York 11797 www. harmankardon. com © 1999 Harman Kardon, Incorporated Part #1111-AVR100OM YIAR-J1000-ZZA AVR 100 Audio/Video Receiver OWNER'S MANUAL Volume Speaker COAX DIGITAL Channel Dig. Select Delay Set SLEEP TAPE CD DVD VID 1 VID 2 VID 3 6 CH. AM/FM TUNING PRESET SCAN PRESET FM MODE DIGITAL PRO LOGIC 3-STEREO HALL THEATER TEST TONE SURR. OFF Power Phones Bass Treble Balance VIDEO 3 Min Max Min Max L R Video L Audio ® Version 7 October 5, 1999 Power for the digital revolution. TM AVR 100 Audio/Video Receiver 3 4 4 5 7 8 10 13 15 19 19 19 20 21 22 23 23 23 23 24 24 24 24 25 25 25 27 28 30 32 33 34 34 35 Introduction Safety Information Unpacking Front-Panel Controls Front-Panel Information Display Rear-Panel Connections Remote Control Functions Installation and Connections System Configuration Operation Basic Operation Source Selection Surround-Mode Selection Surround-Mode Chart Tuner Operation Tape Recording Output-Level Trim Adjustment 6-Channel Direct Input Memory Backup Programming the Remote Direct Code Entry Auto-Search Method Code Readout Programmed Device Functions Resetting the Remote Memory Reassigning the DVD Button Function List Setup Code Tables: TV Setup Code Tables: VCR Setup Code Tables: DVD Setup Code Tables: LD Troubleshooting Guide Processor Reset Technical Specifications Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on the front-panel information display EXAMPLE ­ (outlined type) indicates a lit indicator in the front-panel information display 1 ­ (number in a square) indicates a specific front-panel control a ­ (number in an oval) indicates a button or indicator on the remote ¡ ­ (number in a circle) indicates a rear-panel connection A ­ (letter in a square) indicates an indicator in the front-panel display 2 TABLE OF CONTENTS Introduction Thank you for choosing Harman Kardon! [. . . ] When CEN SP LARGE is selected, a full-range output will be sent to the centerspeaker output, and NO center channel signal will be sent to the subwoofer output. When CEN SP NONE is selected, no signals will be sent to the center-channel output. The receiver will operate in a "phantom" center-channel mode and center-channel information will be sent to the left- and right-front channel outputs. When you have completed your selection for the center channel, press the Set button t 3 , and then press the 1 </ > buttons r on the remote or the Selector buttons 3 on the front 4 panel to change the display to SUR SPEAKER. Press the Set button t 3 again, and 1 then use the </ > buttons r on the remote or the Selector buttons 3 on the 4 front panel to select the option that best describes your system based on the speaker definitions shown in preceding section. When SUR SP SMALL is selected, low-frequency surround-channel sounds will be sent to the subwoofer output only. Note that if you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the surround speaker. When SUR SP LARGE is selected, a full-range output will be sent to the surround-channel outputs, and NO surround channel signals will be sent to the subwoofer output. When SUR SP NONE is selected, surround-sound information will be split between the front-left and front-right outputs. Note that for optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used instead of Dolby Pro Logic. 4. Turn the AVR 100 on either by pressing the System Power Control 2 on the front panel, or via the remote by pressing a Device Selector a on the remote. The Power Indicator 3 will turn green to confirm that the unit is on, and the Information Display 3 will also light up. 5 Speaker Configuration The first few adjustments tell the AVR 100 which type of speakers are in use. This is important as it adjusts the settings that determine which speakers receive low-frequency (bass) information. For each of these settings use the LARGE setting if the speakers for a particular position are traditional full-range loudspeakers that are capable of reproducing sounds below 100Hz. Use the SMALL setting for smaller, frequency-limited satellite speakers that do not reproduce sounds below 100Hz. Note that when "small" speakers are used, a subwoofer is required to reproduce low-frequency sounds. Remember that the "large" and "small" descriptions do not refer to the actual physical size of the speakers, but their ability to reproduce low-frequency 16 SYSTEM CONFIGURATION System Configuration 9. When you have completed your selection for the surround channel, press the Set button t 3 , and then press the </ > 1 buttons r on the remote or the Selector buttons 3 on the front panel 4 to change the display to S-W SPEAKER. Press the Set button t 3 , and then 1 press the </ > buttons r on the remote or the Selector buttons 3 on 4 the front panel to select the option that best describes your system. Select S-W SP YES if a subwoofer is connected to your system. Select S-W SP NO if a subwoofer is NOT connected to your system. [. . . ] If the Program/Command Indicator 37 blinks three times, the code is valid and was accepted by the remote. If the Program/Command Indicator 37 blinks one time, the code is NOT valid and a correct code must be entered. If the code 25 PROGRAMMING THE REMOTE Programming the Remote was valid, look at the product being programmed to see if it turns off. If the VCR to be programmed turned off, press the DVD Device Selector a once to complete the process. [. . . ]