User manual HARMAN KARDON CP 15

[. . . ] SYSTEM REMOTE OWNER'S MANUAL RCP 2 FOR USE WITH CP 15, CP 25 AND CP 35 SYSTEMS RCP 2 SYSTEM REMOTE 2 2 3 7 7 7 7 7 7 8 9 9 9 9 10 10 11 13 RCP 2 System Remote Using EzSet Remote Control Functions Programming the Remote Programming Product Codes Direct Code Entry Auto Search Method Code Readout Learning Codes Macro Programming Volume Punch-Through Channel Control Punch-Through Transport Control Punch-Through Reassigning Device Control Selectors Resetting the RCP 2's Memory Programmed Device Functions Function List Setup Code Tables Trademark acknowledgements on page 23. · The button that is labeled d has no function on the original AVR remote, but on the RCP 2 it has the same function as the AVR 235's SPL Selector Button. Use this button to activate the EzSet feature, which is explained in the AVR 235 manual, and below for CP 15 users. CP 35 users should use the EzSet+ function described in the AVR 335 owner's manual. · The button that is labeled e is the SPL Selector Button on the original AVR 235 remote, but on the RCP 2 that function has been changed to button d. [. . . ] Each press 43 33 29 22 34 29 will30 21 a series of 32 from 42 RCP 2's send out 33 codes the the 28 built-in database. When 31 unit being programmed 31 20 32 turns off, release / /¤ Button n, as that is your indication that the correct code is in use. Press the Input Selector e; the red light under the Input Selector will flash three times before going dark to confirm the entry. Try all of the functions on the RCP 2 to make certain that the product operates. Keep in mind that many manufacturers use a number of different combinations of codes, and it is a good idea to make certain that not only the power control works, but also the volume, channel and transport controls, as appropriate. If all functions do not work properly, you may need to Auto-Search for a different code, or enter a code via the Direct Code Entry method. Code Readout When the code has been entered using the Auto Search method, it is always a good idea to find out the exact code so that it may be easily reentered if necessary. You may also read the codes to verify which device has been programmed to a specific Control Selector button. Press and hold both the Input Selector e for the device you wish to find the code for and the Mute Button 43 at the same time. The 49 47 45 Program/SPL Indicator c will turn amber 48 46 44 42 and begin flashing, and the red light under the 35 37 39 41 Input Selector e will stay lit. Release the but34 36 38 next 37 41 seconds. tons and begin the 40 step within 2047 51 36 40 46 50 33 26 25 37 2. 35 Program/SPL49 The 39 45 32 27 24 36 Indicator c will then blink green in a sequence 31 28 23 34 38 44 48 that corresponds to 35 three-digit code, with a onethe 30 29 22 34 each33 Count 43 numthe second pause between digit. 29 30 21 33 42 32 ber of blinks between each pause to determine the 28 the 20 32 digit of 31 code. One blink is31 number 1, two the blinks is the number 2, and so forth. Ten blinks are used to indicate a "0. " Example: One blink, followed by a one-second pause, followed by six blinks, followed by a one-second pause, followed by ten blinks indicates that the code has been set to 160. For future reference, enter the setup codes for the equipment in your system here: DVD ____________ CD ________________ VID1/VCR __________ VID2/CBL __________ VID2/SAT ________ VID3/TV __________ VID4* ____________ TAPE______________ * The AVR 135 has no Video 4 source input; therefore, remote commands associated with the VID4 button will not have any effect on the AVR 135, although you may use the remote to operate another component. Learning Codes In addition to using codes from the remote's internal code library, the RCP 2 is able to "learn"codes from remotes that may not be in the code library. In addition, this function will allow you to program additional codes from the DVD remote or to "learn over" the codes from a preprogrammed device to add functions not included in the preprogrammed codes. To learn or transfer codes from an IR remote to the RCP 2, follow these steps: 1. Place the front of the original remote with the code being sent so that it is facing the IR Transmitter Window b on the RCP 2 "head-to-head. " The two remotes should be between one and three inches apart. Select the button on the RCP 2 that you wish to use as the device selector for the codes about to be entered. [. . . ] Select Learn Sleep/Ch + Test SPL Volume Up Night/Info Multiroom/Subtitle Volume Down / AVR Function Power On Power Off Mute AVR Select DVD Input Select CD Input Select Tape Input Select Video 1 Select Video 2 Select Video 3 Select Video 4 Select Dim Tuner Select 6/8 Ch. Input Select Learn Sleep Test Tone EzSet/SPL Volume Up Night Mode Select Multiroom Select Volume Down Move/Adjust Up Speaker Adjust Move/Adjust Left Set Move/Adjust Right Digital Input Select Move/Adjust Down Delay Adjust 1 2 3 4 5 6 7 8 Tuner Mode 9 0 Memory DVD Power On Power Off Mute AVR Select DVD Select CD Select Tape Select VCR Select VID2 Select TV Select VID4 Select Dim Tuner Select 6/8 Ch. Select Learn Test TV/DVD EzSet/SPL Volume Up Info Subtitle CD/CD-R Power On Power Off AVR Select DVD Select CD Select Tape Select VCR Select VID2 Select TV Select VID4 Select Dim Tuner Select 6/8 Ch. Select Learn Input Select EzSet/SPL Input Level Up CDP Select Tape VCR (VID1) Power On Power Off Mute CBL (VID2) Power On Power Off Mute AVR Select DVD Select CD Select Tape Select VCR Select CBL Select TV Select VID4 Select Dim Tuner Select 6/8 Ch. [. . . ]