User manual HARMAN KARDON CP 45

[. . . ] AVR 245 AUDIO/VIDEO RECEIVER OWNER'S MANUAL SAFETY INFORMATION home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. This product may be equipped with a polarized alternating-current-line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. [. . . ] The Power Indicator above the two power switches should light up in amber. This indicates that the AVR is in Standby mode and is ready to be turned on. Normally, you may leave the Master Power Switch in the ON position, even when the receiver is not being used. See Figure 57. Sleep Timer You may program the AVR to play for up to 90 minutes and then turn off automatically using the sleep timer. Press the Sleep Button on the remote, and the time until turn-off will be displayed. Each additional press of the Sleep Button will reduce the time until turn-off by 10 minutes, until the OFF setting is reached, which disables the sleep timer. Figure 57 ­ Power Switches There are several ways in which the AVR 245 may be turned on: a) Press the Standby/On Switch on the front panel. b) Press the Source Select Button on the front panel. See Figure 58. Figure 60 ­ Sleep Button When the sleep timer has been set, the front-panel display will automatically dim to half-brightness. If you press any button on the remote or front panel, the display will return to full-brightness. The display will dim again several seconds after your last command. If you press the Sleep Button after the timer has been set, the remaining time until turn-off will be displayed. You may press the Sleep Button to change the time until turn-off. Pressing and holding the Sleep Button will disable the sleep timer, and the SLEEP OFF message will appear. Figure 58 ­ Source Select Button Volume Control The volume may be adjusted either by turning the knob on the front panel (clockwise to increase volume or counterclockwise to decrease volume), or by pressing the Volume Control Buttons on the remote. The volume is displayed as a negative number of decibels (dB) below the 0dB reference point, and may be changed in 0. 5dB increments. Unlike some volume controls on other products, 0dB is the maximum volume for the AVR 245. Although it's physically possible to turn the volume to a higher level, doing so may damage your hearing and your speakers. For certain more dynamic audio materials, even 0dB may be too high, allowing for damage to equipment. c) Using the remote, press any one of these buttons: AVR, DVD, CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, VID4, XM, AM/FM, 6/8CH. See Figure 59. Figure 59 ­ AVR and Input Selectors NOTE: Any time you press one of the remote's Input Selectors (i. e. , DVD/CD, TAPE/The Bridge, XM, VID1, VID2, VID3, VID4 or HDMI 1/HDMI 2), the remote will switch modes so that it will transmit only the codes programmed to operate that device. In order to control the receiver, you will need to press the AVR Button to return the remote to AVR mode. To turn the receiver off, press either the Standby/On Switch on the front panel, or press the AVR Button and the OFF Button on the remote. Unless the receiver will not be used for an extended period of time (for 36 Figure 61 ­ Volume Controls The AVR 245 is designed to reproduce audio with a minimum amount of distortion, which may lead you to think that your hearing and the equipment can handle higher volumes. We urge caution with regard to volume levels. OPERATION Mute Function To temporarily mute all speakers and the headphones, press the Mute Button on the remote. [. . . ] Input Select Tape VCR (VID1) Power On Power Off TiVo (VID1) Power On/Off TV Power Mute AVR Select DVD Select CD Select Tape Select HDMI 1 Select HDMI 2 Select VCR Select CBL/SAT Select TV Select Video 4 Select XM Select Tuner Select 6/8 Ch. Input Select Channel + TV Input Volume Up Channel ­ Live TV CBL (VID2) Power On Power Off Mute AVR Select DVD Select CD Select Tape Select HDMI 1 Select HDMI 2 Select VCR Select CBL Select TV Select Video 4 Select XM Select Tuner Select 6/8 Ch. Input Select Channel + TV/CBL Channel ­ OSD SAT (VID2) Power On Power Off Mute AVR Select DVD Select CD Select Tape Select HDMI 1 Select HDMI 2 Select VCR Select SAT Select TV Select Video 4 Select XM Select Tuner Select 6/8 Ch. Input Select Channel + TV/SAT Volume Up Channel ­ OSD Volume Down TV (VID3/VID4) Power On Power Off Mute AVR Select DVD Select CD Select Tape Select The Bridge (DMP) Select HDMI 1 Select HDMI 2 Select VCR Select CBL/SAT Select TV Select Video 4 Select XM Select Tuner Select 6/8 Ch. [. . . ]