User manual HARMAN KARDON CP 65

[. . . ] RCP 7 SYSTEM REMOTE OWNER'S MANUAL (FOR USE WITH CP 65 SYSTEM) TABLE OF CONTENTS 3 4 9 10 12 13 13 13 14 15 16 18 18 19 20 20 21 21 21 22 INTRODUCTION AND FEATURES REMOTE CONTROL FUNCTIONS BATTERIES PROGRAMMING SOURCES LEARNING INDIVIDUAL KEY CODES ADVANCED FUNCTIONS Punch-Through Programming Macros Resetting the Remote APPENDIX Remote Control Function List Remote Control Product Codes TV VCR CD DVD SAT TAPE CBL The Bridge/DMP 2 INTRODUCTION AND FEATURES Please register your product on our Web site at www. harmankardon. com. Note: You'll need the product's serial number. At the same time, you can choose to be notified about our new products and/or special promotions. WWW. HARMANKARDON. COM Thank you for choosing Harman Kardon! Your Harman Kardon® CP Series system combines the superior performance and practical flexibility of high-quality separate audio/video components with the convenience of a complete system in one carton. You will need to provide a video display or television, but you may also add almost any source device, ranging from a cassette deck or VCR all the way up to the latest digital cable or satellite television set-top box (or even products that may be released in the future). The single RCP 7 remote replaces the original remotes supplied with the AVR 347 receiver and DVD 48 DVD player. [. . . ] The selector will retain this selection until the next time you toggle between the primary and secondary device modes. That is, if you press the DVD/CD Selector twice quickly so that the CD source is activated, then press another source selector, such as Video 1, the next time you press the DVD/CD Selector, the remote will return to the CD device mode. The RCP 7 remote is factory-programmed to control the AVR 347, the DVD 48 and an iPod docked in The Bridge. If you have other source devices in your system, such as a VCR, or a cable or satellite television set-top box, follow these steps to program the correct codes into the remote: 1. Using the codes in Tables A2­A9 of the Appendix, look up the product type (e. g. , cable TV box) and the brand name of your source. The number(s) listed are potential candidates for the correct code set for your particular device. This step places the remote in Program mode and varies slightly, depending on which Input Selector is being programmed. a) DVD, Tape, Video 1, Video 2, Video 3 and Video 4 Sources: Press and hold the Input Selector until the Program Indicator LED starts to flash, then release it. b) CD Source: Press the DVD/CD Input Selector twice quickly so that it turns green. Then press and hold it until the selector relights and the Program LED flashes. Follow the directions in Step 4. 10 Figure 2 ­ Input Selectors c) HDMI 1 Source: Press and hold the Input Selector until the Program Indicator flashes, then release it. Next, press the Input Selector that corresponds to the device type you want to program into the HDMI 1 mode, i. e. , DVD, VCR or CBL/SAT. d) HDMI 2 Source: Press and release the Input Selector once, quickly press the Input Selector again so that it turns green, then release it. Now press and hold the Input Selector until the Program Indicator flashes, then release it. Next press the Input Selector that corresponds to the device type you want to program into the HDMI 2 mode, i. e. , DVD, VCR or CBL/SAT. Then follow the directions in Step 4. 4. a) If the device turns off, then press the Input Selector again to accept the code; the selector will flash. b) If the device does not turn off, try entering another code. If you run out of codes, you may search through all of the codes in the remote's library for that product type by pressing the / or ¤ Button repeatedly until the device turns off. When the device turns off, enter the code by pressing the Input Selector, which will flash. NOTE: When you enter a valid three-digit code, the Program Indicator LED will change in color to green. However, entering an invalid code changes the color of the LED to red. [. . . ] Input Select Learn Power On (AVR) Power On Power Off (AVR) Power Off Mute (AVR) Mute AVR Select DVD Select CD Select Tape Select AVR Select DVD Input Select CD Input Select Tape Select Bridge TM Tape Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Selectt 7 HDMI 1/HDMI 2 HDMI 1 Select HDMI 2 Select 8 VID 1 (VCR) 10 VID 3 (TV) 11 VID 4 12 XM 13 AM/FM 14 6/8CH 15 Learn 17 Test Tone 18 T/V/V. Off 19 Vol Up 20 Surr/Title Volume Up* DSP Surround Mode Select Title Group HDMI Volume Down Disc Menu Setup Continuous Play Intro Scan Input Menu Up Left Enter Right Down Open/Close 1 2 3 4 5 6 7 8 Eject Speed 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Guide Menu Up Left Select Right Down Return/Exit Prev. Channel 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Prev. Channel 1 2 3 4 5 6 7 8 Info Menu Up Left Enter Right Down Info Menu Up Left Enter Right Down Menu Up Left Enter Right Down Scroll ­ Select Scroll + Menu Up Left Set Right Down Volume Down Guide Menu Up Left Set/Enter Right Down Video 1 Select 9 VID 2 (CBL/SAT) Video 2 Select Video 4 Select XM Select Tuner Select 6/8 Ch. Input Select Learn Test Tone Input Select Volume Up CDR Select Program Channel ­ OSD TV/VCR TV/Video Volume Up Channel ­ OSD HDMI 1 Select HDMI 1 Select HDMI 2 Select HDMI 2 Select VCR Select TV Select XM Select Tuner Select Learn VCR Select TV Select XM Select Tuner Select Learn Channel + CBL/SAT Select CBL/SAT Select Video 4 Select Video 4 Select Video 3 Select TV Select 6/8 Ch. [. . . ]