User manual HARMAN KARDON DRIVE + PLAY [HK-DP1EU]

[. . . ] Owner's Manual INTRODUCTION Thank you for purchasing Harman Kardon's Drive + PlayTM, an elegant mobile audio solution that provides the driver with easy iPod® control, including full music browsing capability. We've organized this manual to make installation and operation as simple and trouble-free as possible. Please read it thoroughly before you begin installing Drive + Play. For the answers to many commonly-asked questions regarding installation and use of Drive + Play, please visit us at: www. harmankardon. com Drive + Play Warnings Distraction Warning Do not connect or disconnect your iPod or program Drive + Play while driving. [. . . ] For screw mounting, the cable can be routed through the center of the base and through a hole that must be drilled in the mounting surface. You may use the mounting plate as a template. continued on next page. . . Control Knob 0° Base Cable Through 0° Base and Internal Mounting Plate Internal Mounting Plate INSTALLATION 7 Installing Components Installing the Control Knob (continued) 2. At the base (below the cable), using the 1. 5mm hex key, loosen (but do not remove) the hex setscrew. To install the Control Knob with adhesive tape, perform the following steps or skip to step 4: a. Insert the mounting plate, rotate it 180°, and tighten the hex setscrew. Mounting Plate Arrow Control Knob With 0° Base Control Knob With 0° Base 5. Route the attached cable to the Electronics Enclosure. Installing the iPod Cable Route the iPod dock connector cable to the chosen iPod site (e. g. , the center console compartment or the glove box). Be sure to leave enough cable exposed to make connecting and disconnecting the iPod easy. Making the System Connections With all power off, refer to the Wiring Diagram on page 5 and make only the power, ground and audio signal connections that apply to the scheme you have chosen. Make sure all the plugs are properly seated in their receptacles. Mounting Plate Adhesive Pad b. To ensure adhesion, wipe the surface at the site and exposed mounting plate with one of the enclosed alcohol pads. Remove the protective tape from one side of one of the enclosed adhesive pads, and press the pad against the mounting plate. Remove the remaining protective tape, and press and hold the Control Knob to its site for 5 seconds. To install the Control Knob with mounting screws, perform the following steps: a. At the proposed site, place the mounting plate and rotate it so that the arrow will point toward the hex setscrew at the back of the base after it's mounted. Holding the mounting plate in position, fasten it to the surface with three enclosed mounting screws. Using the mounting plate's center hole as a template, drill a hole through the mounting surface and pass the Control Knob's cable through the hole. Place the Control Knob on the mounting plate (180° from its final position), and then rotate it a half-turn to the final position. Tighten the hex setscrew at the back of the base. OPERATING DRIVE + PLAY Distraction Warning Do not connect or disconnect your iPod or program Drive + Play while driving. Always pull off the road and park in a position that you are absolutely sure presents no risk before browsing your iPod or adjusting the settings on your Drive + Play. Always obey all traffic laws while driving. Overview Scroll Left Once to Last Menu Item Scroll Ring Press Once to Jump to Last Screen Menu Scroll Ring Scroll Left and Hold to Jump Back In Now Playing, Scroll Left to Fast Rewind Press Once to Play Last Track Press and Hold to Rewind Scroll Right Once to Next Menu Item Scroll Right and Hold to Jump Forward In Now Playing, Scroll Right to Fast Forward Previous/Rewind Next/Fast Forward Press Once to Play Next Track Press and Hold to Fast Forward Press Once to Choose Play/Pause Highlighted Menu Item Press Once to Stop or Resume Play of Current Track Select Drive + Play On/Off Press Once to Turn On Press and Hold to Turn Off 8 INSTALLATION/OPERATION OPERATION Drive + Play operates much like the iPod itself. The Control Knob mimics the iPod's Click Wheel, and its software uses a similar menu-select system. [. . . ] Repeat step 2 for other menus you want to remove from or add to the Main Menu. NOTE: Drive + Play will store up to 32 characters for display in the Now Playing screen, arranging the names of songs in logical groups of characters. To display the next logical group, press the Select button once. If there are more characters than can be displayed in two NOTE: Settings cannot be removed from the Main Menu. 10 OPERATION OPERATION Setting the Sleep Timer Drive + Play is equipped with a sleep timer that delays its power off by a default of 2 seconds after the ignition is turned off. During the delay, Drive + Play will display "powering off. " You can set a different delay time as follows: Now Playing Song Title Artist TO1 0:00 NOTE: Sleep Timer only works when the Drive + Play's ACC wire is connected to the ignition switch's accessory terminal (see Wiring Diagram on page 5). · Drive + Play Menu > Settings > Sleep Timer > select 2 sec (default), 4 sec, or 8 sec. NOTE: Now Playing, Playlists, Artists, Albums, Songs, Genres or Composers will only appear in the Main Menu after they have been checked for display (see the previous page). Browsing Playlists · Drive + Play Menu > Playlists > select a playlist (e. g. , Favorites) > select a song. Setting the Jump Size When browsing a database (songs, albums, artists, etc. ), you can scroll and hold to jump to a different position in the list, skipping over undesired titles. [. . . ]