User manual HARMAN KARDON DVD 506 LIMITED EDITION

[. . . ] DVD 506 Limited Edition Digital Versatile Disc Player OWNER'S MANUAL ® Power for the Digital Revolution® Table of Contents 3 4 5 6 7 8 10 11 11 12 13 14 15 16 16 16 17 17 18 18 19 19 19 19 20 21 Introduction Terminology Features, Packing List Front Panel Controls Front Panel Information Display Remote Control Rear Panel Connections Setup and Connections to a Stereo TV and Stereo or Pro Logic Amplifier/Receiver to a Dolby Digital/DTS Amplifier/Receiver to a TV or monitor with SCART or Component Connectors Remote Control Digital Audio Connections Playback Basics Basic Play Playback Features System Set-up System Settings Audio Settings Video Settings Using the Status Bar Player Menu Information Displays Programmed Play DVD Language Codes Specifications Declaration of Conformity We, Harman Consumer International 2, Route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 60 065:1993 EN 55 013/A12/8. 1994 EN 55 020/12. 1994 EN 61000-3-2/4. 1995 EN 61000-3-3/1. 1995 Carsten Olesen Harman Kardon Europe 10/03 NOTE: This player is designed and manufactured for compatibility with Region Management Information that is encoded on most DVD discs. This player is designed only for playback of discs with Region Code 2, or for discs that do not contain Region Code information. If there is any other Region Code on a disc, that disc will not play on the DVD. 2 2 TABLE OF CONTENTS Introduction Thank you for choosing the Harman Kardon DVD. The DVD is a multipurpose DVD player, capable of playing both DVD-Video discs and conventional CD audio discs with the highest fidelity and access to future software upgrades via the Internet. [. . . ] Connect the video or S-video output of the DVD player (whatever is provided with your device) to the video or S-video input on your device and the video/S-video output of this device to your TV. For more details, see the manual of your Audio/Video amplifier/receiver. I Note for Analog Audio: The connection from Audio Out to the TV is optional only. Normally you´ll hear the sound from your AV-system´s speakers, so the TV volume should be completely turned down. If you plan to use your DVD player also without having to turn on your complete system, this connection must exist, then you can turn up the TV´s volume as needed. TV To S-Video input connector To audio input connector (Red/White, optional only, see Note above) To Video input connector (Yellow) To power outlet (AC 230V/50 Hz) DVD To coaxial audio input connector To optical audio input connector Dolby Digital or DTS decoder Front Speaker (Left/Right) Center Speaker Surround Speaker (Left/Right) Subwoofer 12 SETUP AND CONNECTIONS Setup and Connections Connecting to a TV or monitor with SCART or Component connectors Important Notes on SCART and RGB format: I Your DVD is equipped with a SCART connector for direct connection to the TV. I The SCART connector provides the video signal as well as audio (stereo L/R) signals. I The SCART connector for the TV provides the composite video signal or the direct RGB signal, delivering the best video performance possible, selectable in the Setup menu. To view RGB video on your TV, the RGB compatible SCART connector on the TV must be used and the DVD´s TV SCART connector must be set to "RGB". Note that with RGB video the color intensity cannot be adjusted with most TVs. I When the RGB video signal is used, DVD´s recorded with the NTSC format (with regional code 0 or 2) can be viewed even on nonNTSC compatible TVs. Component Video Connection If the video display has component video inputs, connect the Component Video Outputs on the DVD to the corresponding input jacks on your television. If you are using a progressive scan television or projector, you must also change the Scan Type in the DVD player's Video Set-Up Menu from "Interlaced" to "Progressive". TV or Monitor To SCART connector DVD To Component connectors To power outlet (AC 230V/50 Hz) To optical or coaxial input of Dolby Digital/ DTS Decoder/ Amplifier/Receiver SETUP AND CONNECTIONS 13 Remote Control Battery installation Insert the batteries supplied while observing the correct (+) and (­) polarities. Remote control operation range Point the remote control unit from no more than about 7 m from the remote control sensor and within about 60 degrees of the front of the unit. Service life of batteries I The batteries normally last for about one year, although this depends on how often, and for what operations, the remote control is used. I If the remote control unit fails to work even when it is operated near the player, replace the batteries. Notes: I Do not attempt to recharge, short-circuit, disassemble, heat or throw the batteries into fire. I Do not drop, step on or otherwise impact the remote control unit. This may damage the parts or lead to malfunction. I Wipe away any leakage inside the remote control unit, and install new batteries. I If leakage should come into contact with parts of your body, wash it off thoroughly with water. I Batteries contain chemical substances and we recommend that you dispose of them properly and in compliance with any local regulations. Do not simply throw them away but return to your dealer or special battery disposal centers. I The operating distance may vary according to the brightness of the room. Notes: I Do not point bright lights at the remote control sensor. I Do not place objects between the remote control unit and the remote control sensor. I Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment. 14 REMOTE CONTROL Digital Audio Connections Audio output from the unit's optical/coaxial digital audio output connector Disc: DVD Sound recording Optical/Coaxial digital audio output format: Dolby Digital (AC-3) Linear PCM (48/96 kHz 16/20/24bit) DTS MPEG (2. 0) Dolby Digital bitstream (2-5. 1 ch) or PCM (2 ch, 48 kHz/16bit)* Linear PCM (2 ch) (48/96 kHz 16/20/24bit) DTS Bitstream or no output * MPEG bitstream (2ch) or linear PCM (2 ch, 48kHz) Linear PCM* Linear PCM (44. 1 kHz sampling) For your reference: I Dolby Digital (AC-3) is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation, supporting 5. 1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc. [. . . ] Move the cursor to the right of the menu, into the Disc List. Move the cursor up or down to the first track you would like to program and press ENTER. The cursor will move to the options in the Lower Menu Line. You can either add the selected track (or picture) to the playlist or give it the number you would like it to have in your playlist, or clear the track from the list. [. . . ]