User manual HARMAN KARDON FL8350

[. . . ] Harman Kardon FL8350 Compact Disc Changer 1 2 3 1 DISC fl 2 TRACK 3 4 MIN Skip Play Pause 5 SEC 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 4 5 Disc Skip Search Stop Random Open/Close Time Repeat Intro Clear Program Owner's Manual Staple or clip original invoice here. w Owner's Manual FL8350 Compact Disc Changer Table of Contents Introduction . 16 250 Crossways Park Drive Woodbury, NY 11797 ©1998 Harman Kardon, Incorporated Introduction 1 Thank you for choosing the Harman Kardon FL8350 CD changer. The FL8350 is an exceptionally well-engineered product that offers high performance and ease of use. [. . . ] Install the two AA batteries supplied with the FL8350's remote by turning the remote over so that you are holding the bottom side up. Press lightly on the embossed arrow on the cover, and gently slide the cover towards you in the direction of the arrow. Insert the batteries inside the compartment, being careful to follow the + and ­ polarity indications at the bottom of the compartment. Replace the cover by placing it on the remote and sliding it back towards the top of the remote. NOTE: When replacing batteries it is always a good idea to replace both at the same time. When the unit will not be used for an extended period of time, it is also a good idea to remove the batteries so that the potential for corrosion or damage is avoided. Connect the power to a non-switched AC wall outlet, or to the accessory outlet on the rear of another audio device in your system and you are ready to go!NOTE: When using the accessory outlet on another product to power the FL8350 make certain that it has the ability to power a device that draws at least 20 watts of current in addition to the requirements of other devices that may be plugged into the accessory outlets. If you use a "switched" outlet, it is important to remember that the host product must be turned on in order for the FL8350 to operate. © Operation 10 Loading Discs To load a disc, first turn the FL8350 on using the Power Switch 1. Note that the Status Mode Indicator 2 will turn green and the Information Display Ó will illuminate. The word disc will flash in the Information Display, and the disc tray will automatically turn clockwise so that the FL8350 can sense which, if any, of the disc positions already have a disc. To load a disc, first press the Open/Close button !a, taking care to make certain that the space in front of the drawer is not obstructed. Note that if the drawer is blocked when attempting to open it, it will automatically close within five seconds to protect the mechanism. Load discs in the tray with the printed (label) side facing up towards you. Make certain that the disc is centered in the tray. Either 5" (12cm) or 3" (8cm) discs may be used. When a 3" (8cm) disc is played, it should be carefully centered within the smaller ridges on the tray. Only one CD may be placed in any position at a time. When a 3" (8cm) is played, DO NOT place a standard 5" (12cm) disc over the smaller disc. Labeled surface Note that each disc position has a number embossed in the plastic tray. This corresponds to the position this disc will occupy for playback and programming. To make it easier to identify each disc's position, the disc position number for the holder space that is in the center of the disc tray will also appear in the Information Display when the disc drawer is open. To rotate the disc tray to another position, press the Disc Skip button * p. [. . . ] After the entire program has been played, the FL8350 will stop. As long as the Stop button % g has not been pressed, and the PROGRAM indicator remains lit, you may repeat the programmed play sequence again by pressing the Play button $ h. Pressing the Stop button % g, opening the disc drawer by pressing the Open/Close button !a or turning the FL8350 off will erase the program information from the unit's memory. Checking Program Contents To check the contents of a program while the unit is stopped, press the Skip buttons ^ f and the Information Display will step through each of the programmed discs and tracks. Clearing Programs When the unit is stopped, but the PROGRAM indicator is still lit, you may clear the entire contents of a program by pressing the Clear button 9 m. Programmed Play Operation 14 Repeat Play The FL8350's programming system enables you to repeat either all of the tracks on all of the discs, a complete single disc or a single track. [. . . ]