User manual HARMAN KARDON HD 990

[. . . ] HD 990 CD Player OWNER'S MANUAL ENGLISH Table of Contents 2 3 4 4 5 6 7 9 10 10 10 11 11 11 12 12 12 12 12 13 13 13 13 14 15 16 Typographic Conventions Introduction Information Unpacking Front Panel Controls Rear Panel Connections Remote Control Functions Installation Operation Loading and Unloading Discs Normal Play Display Dim Time Display Disc Info Search Skip Folder +10/-10 Input/Source Selection Programmed Play Operation Programmed Play Checking Program Contents Clearing Programs Repeat Play Troubleshooting Guide Technical Specifications Declaration of Conformity We, Harman Consumer Group International 2, route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55013:2001+A1:2003 EN 55020:2002+A1:2003 EN 61000-3-2:2000 EN 61000-3-3. 1995+A1:2001 EN 60065:2002 Jurjen Amsterdam Harman Consumer Group International 06/08 Typographic Conventions In order to help you use this manual with the remote control, front panel controls and rear panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front panel button, or rear panel connection jack. EXAMPLE ­ (bold type) indicates a message in the front panel information display. 1 ­ (number in a square) indicates a specific front panel control. [. . . ] When the unit is turned off (to Standby), pressing the Play button 4 9 on the front or on the remote will automatically turn on the CD player and start playback. Also, pressing the Open/Close button from Standby switches on the player directly and opens the drawer. Load the disc in the tray with the printed (label) side facing up. Make certain that the disc is centered in the tray. Either 12cm (5") or 8cm (3") discs may be used. When an 8cm disc is played, it should be carefully centered within the smaller ridges inside the cassette drawer. To remove a disc from the player, press the Open/Close button 3 F. The drawer will open, allowing the disc to be removed. Disc Handling Notes When loading or unloading discs, it is best to hold them by the edges. While Compact Discs are very reliable, rough handling may damage them. Avoid scratching the bottom (non-printed) side of discs, or any handling which will leave fingerprints. To avoid damage to the disc and player, always seat discs so that they are centered in the tray. Do not lift the player while the disc tray is opening or closing, as this may cause the disc to unseat from the tray and possibly jam. Pressing the Open/Close button once a disc has been carefully seated will close the disc drawer while the message CLOSING will appear in the information display. As soon as the tray is closed the display will show the message READING while the Table Of Contents (TOC) of the disc is read. Note that particulary with CD-RW discs this tracking may take some time due to the reflectibility and data structure being different from normal discs. Afterwards, the Information Display will show the total number of tracks and the total running time of the disc. Note that with MP3-CDs, the total running time will not be shown. _ AB TRACK AUTO MIN SEC HOUR Normal Play To play a disc, first turn the HD 990 on using the Power Switch 2 on the front panel or the Power On button 1 on the remote control. When the unit is turned off (to Standby), pressing the Play button 4 9 on the front or on the remote will automatically turn on the CD player and start playback. The drawer will also close when the Play button 4 9 is pressed. The drawer will close and the disc will start playing the first track. To play all of the tracks on the disc in order, press the Play button 4 9. A play symbol fl will appear in the Information Display 1, as well as indication of Track number and Time elapsed. . [. . . ] Repeat A­B The CD player may be programmed to repeat any section within a track, or a complete passage or program that includes material in a series of tracks. To program the unit for A­B play, first locate the point on the disc where you wish to begin the repeated section. At that point, press the Repeat A­B button 6. The REPEAT indicators will light in the Information Display and an A­ indicator to show that the program process has started. [. . . ]