User manual HARMAN KARDON HD 950

[. . . ] 30525_HD_950_Eng 20/10/06 8:58 Side 1 HD 950 CD Player OWNER'S MANUAL HD 9 0 Play Pause Stop SKip/Search Display ENGLISH 30525_HD_950_Eng 20/10/06 8:58 Side 2 Table of Contents 2 3 4 4 5 6 7 9 10 10 10 11 11 11 12 12 12 12 13 13 13 13 14 15 16 Typographic Conventions Introduction Information Unpacking Front Panel Controls Rear Panel Connections Remote Control Functions Installation Operation Loading and Unloading Discs Normal Play Display Dim Time Display Disc Info Search Skip Folder +10/-10 Programmed Play Operation Programmed Play Checking Program Contents Clearing Programs Repeat Play Troubleshooting Guide Technical Specifications Declaration of Conformity We, Harman Consumer Group, Inc. 2, route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55013:2001+A1:2003 EN 55020:2002+A1:2003 EN 61000-3-2:2000 EN 61000-3-3. 1995+A1:2001 EN 60065:2002 Jurjen Amsterdam Harman Consumer Group, Inc. 09/06 Typographic Conventions In order to help you use this manual with the remote control, front panel controls and rear panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front panel button, or rear panel connection jack. [. . . ] As soon as the tray is closed the display will show the message READING while the table of content (TOC) of the disc is read. Note that particulary with CD-RW discs this tracking may take some time due to the reflectibility and data structure different from normal discs. Afterwards the Information Display will show the total number of tracks on a disc and the total running time of the disc. Note that with MP3-CDs the total running time will not be shown. _ AB TRACK AUTO MIN SEC HOUR Normal Play To play a disc, first turn the HD 950 on using the Power Switch 2 on the front panel or the Power On button 1 on the remote control. When the unit is turned off (to Standby), pressing the Play button 4 9 on the front or on the remote will automatically turn on the CD player and start playback. To load or change a disc open the disc drawer by pressing the Open/Close button 3 F. Place a disc in the tray following the instructions shown above. The drawer will also close when the Play button 4 9 is pressed. The drawer will close and the disc will start playing the first track. To play all of the tracks on the disc in order, press the Play button 4 9. A play indication fl will appear in the Information Display 1. To play all of the tracks in random order, press the Random button C. The RANDOM indicator will light when that mode is in use. Random can be activated also while a track is playing. When Random is activated while programmed play is in use (see page 13), all programmed tracks will be played in random order. You may also select a specific track by pressing the Skip buttons 7 7 until the desired track number is displayed (see page 12). The track may also be selected directly by entering the track number via the Numeric Controls 2, simply enter the track number by pressing the buttons that correspond to the desired track. Note that when a two- or three-digit track number is being entered, the second and third digit of the number must be pressed within two seconds of the first digit. After the track is selected, press the Play button 4 9. Labeled Surface To retract the drawer back into the player after loading a disc, press the Open/Close button 3 F. When the drawer is closed the display will indicate the total number of tracks on the disc and the total running time of the disc. The drawer will also close when the Play button 4 9 is pressed. The drawer will close and the disc will start playing the first track. 10 OPERATION 30525_HD_950_Eng 20/10/06 8:58 Side 11 Operation While the disc is playing, the track being played will show as a number in the middle of the display just below the word TRACK. The elapsed time of the track being played will also appear in the display (see figure page 10). [. . . ] The disc will play continually until the Stop button 6 A is pressed. Repeat A­B The CD player may be programmed to repeat any section within a track, or a complete passage or program that includes material in a series of tracks. To program the unit for A­B play, first locate the point on the disc where you wish to begin the repeated section. At that point, press the Repeat A­B button 6. [. . . ]