User manual HARMAN KARDON HD100

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inteference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: USE OF ALL CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. [. . . ] Open and close the drawer using the OPEN/ CLOSE button (3). 6. PLAY BUTTON ( ) This button is used for starting play. 12. PROGRAM/CHECK BUTTON This button is used for checking the stored tracks. 17. BACKWARD SKIP BUTTON ( ) This button is used for replaying from the beginning of the current track or returning to a previous track. 7. PAUSE BUTTON ( ) This button is used for holding play at the start of a track or interrupting play. 13. TIME BUTTON This button is used for checking the elapsed playing time from the beginning of current track or remaining playing time of current track or remaining playing time of disc. 3. OPEN/CLOSE BUTTON ( ) Press this button to open or close the compact disc drawer. The drawer will also close if you press the play button or push the drawer gently toward the chassis of the player; however, we recommend that you do not push the drawer. 18. FORWARD SKIP BUTTON ( ) This button is used for moving onto the next track. 8. STOP/CLEAR BUTTON ( ) This button is used for stopping play or clearing programmed tracks. 14. DISPLAY BUTTON This button is used to dim the display lighting, if desired. 19. PROGRAMMING Example: If you wish to program the tracks 4, 8 and 17, the programming procedure is as follows. In the stop mode, press the PROGRAM button, the MEMORY light in the display will start blinking. DISC TRACK MEMORY MIN SEC SEARCHING A SPECIFIC PASSAGE IN PLAY MODE 4. Repeat steps 2 and 3 to complete programming. DISC TRACK INDEX STEP MEMORY TOTAL · Press the REPEAT button before or during play. · Press and hold down the FORWARD or BACKWARD SEARCH button ( / ) and release the button when the desired point has been reached. 4 9 · REPEAT ALL appears on the display and all tracks of the CD will be repeated. the last track during forward search, the unit goes back to the beginning of the first track and continues to search forward. ¬ TRACK MEMORY TOTAL DISC · If the CD player reaches the end of the last track during forward search, the unit switches to the stop mode. · If the CD player reaches the end of 4 17 8 · If the CD player reaches the beginning of a CD during backward search in normal play mode, play restarts at this point. 5. Press the PLAY button. · After the last programmed track has been played, the last programmed track number and the total playing time of the programmed tracks are shown on the display. REPEAT ONE TRACK · After selecting a desired track with the FORWARD or BACKWARD SKIP button, press the REPEAT button twice before or during play. · If the CD player reaches the beginning of a track during backward search in random or programmed play mode, play restarts at this point. 1 11 2 12 3 13 4 14 5 15 6 16 7 17 8 18 9 19 10 20 OVER · During program play, if you want normal play, select the desired track with the NUMERIC buttons, then normal play will start that track. · REPEAT appears on the display and the selected track will be repeated. ONE 2. Select the desired track with the SKIP buttons or NUMERIC buttons on the remote. DISC TRACK MEMORY · If the REPEAT button is pressed once again in this mode, repeat play mode is canceled. · If you want program play again, press 4 the PROGRAM button in the stop mode, then the unit switches to the program mode. 3. The TOTAL light and the program number (1-20) in the display will illuminate. DISC TRACK MEMORY TOTAL 4 7 Uden navn-1 10 12/01/1998, 14:47 CHECKING THE CONTENTS OF THE PROGRAM You can check the contents of the program during programming or after completion of programming. RANDOM PLAY In this mode, CD player plays the tracks on the CD in random sequence. NOTE: ENGLISH · Press the RANDOM PLAY button. The unit automatically selects and plays tracks at random. When a track of which number is greater than 30 is programmed or being played, or during random play, the time display may show "­ ­:­ ­". · Each time the PROGRAM/CHECK button is pressed, the programmed tracks will appear in the programmed sequence. CLEARING THE PROGRAMMED TRACKS DISPLAY DIMMING · Pressing the DISPLAY button deletes all indicators in the display, only the (selected) track indication remains in STOP or PAUSE mode. · If the RANDOM PLAY button is pressed during random play, random play is canceled and normal play starts at the present track. · Each time the STOP/CLEAR button is pressed during programming or after completion of programming, the programmed tracks are cleared one by one in the opposite sequence. TIME DISPLAY SELECTION In addition to displaying the elapsed time of the currently playing track, this unit has two other time display modes. One mode will indicate the total time remaining on the disc (TOTAL will light in the display). The other mode will indicate the time remaining on a specific track (EACH will light in the display). · While running even this track indication is deleted, leaving only a small dot in the display as reminder that the unit is still running. In that mode if any button (except PLAY) is pressed, the track is indicated again for a short moment. · If you wish to clear a specific track, find that track with the PROGRAM/ CHECK button and clear with the STOP/CLEAR button. · Pressing the DISPLAY button again returns to the normal display indication. · By pressing the OPEN/CLOSE or STOP/CLEAR button over 4 seconds in the stop mode, all programmed tracks will be cleared. · Change the time display selection by repeatedly pressing theTIME button. AUTO EDIT IS COMPLETED 8 Uden navn-1 11 12/01/1998, 14:47 Remote Control The remote control for the HD100 provides the same functions found on the front panel of the compact disc player itself. [. . . ] However, it is safe to experiment. · If you want to cancel repeat A play, press the A CLEAR button. B or STOP/ B 9 Uden navn-1 12 12/01/1998, 14:47 CONCERNING USE OF BATTERIES Two batteries are provided with your remote control. Locate the cover over the battery compartment on the back of the remote control. Remove the cover by sliding it in the direction of the embossed arrow. [. . . ]