User manual HARMAN KARDON HK 3370

[. . . ] HK 3370 Stereo Receiver OWNER'S MANUAL MUTE T-MON RDS PTY CT RT TA AUTO TUNED ST MEMORY PRESET SLEEP Power for the Digital RevolutionTM Table of Contents 3 Introduction 3 Important Information 4 Front Panel Controls 6 Rear Panel Connections 8 Remote Control Functions 10 Installation and Connections 12 Operation 12 12 12 13 14 14 14 15 Basic Operation Source Selection Tuner Operation RDS Operation Tape Recording Memory Backup Processor Reset Using the Remote Control Declaration of Conformity We, Harman Consumer International 2, Route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55013/6. 1990 EN 55020/12. 1994 EN 60065:1993 EN 61000-3-2/4. 1995 16 Troubleshooting Guide 17 Technical Specifications Carsten Olesen Harman Kardon Europe A/S 02/01 Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on the front-panel information display 1 ­ (number in a square) indicates a specific front panel control å ­ (letter in a circle) indicates a button or indicator on the remote 0 ­ (number in a circle) indicates a rear panel connection 2 TABLE OF CONTENTS Introduction Congratulations!With the purchase of the Harman Kardon HK 3370 you are about to begin many years of listening enjoyment. While sophisticated systems are hard at work within the HK 3370 to make all of this happen, hookup and operation are simple. [. . . ] When an optional, powered subwoofer (not the aktive Sub of a Sub/Sat-System) is used, connect the outputs of the left and right Subwoofer Out jacks F to the line-level inputs of the subwoofer. When the subwoofer's amplifier has stereo inputs, run interconnects from both jacks. When the subwoofer has a mono input only, use the bottom output jack for the connection. When a separate passive subwoofer is used, these connections will be made to the optional amplifier that powers the subwoofer. If a Sub/Sat system is used (aktive or passive), connect the Speaker 1 terminals G to the speaker-level inputs on the subwoofer, and then connect the speaker-level outputs on the subwoofer to your main left and right speakers, following the instructions provided with the subwoofer. 7. Connect an FM antenna to the FM Antenna connection 1. The FM antenna may be an external roof antenna, an inside powered or wire lead antenna or a connection from a cable system. Note that if the antenna or connection uses 300-ohm twin-lead cable, you must use the 300-ohm-to-75-ohm adapter supplied with the unit to make the connection. If you wish to use external processing equipment, such as an equalizer, you may connect the device to the preamp-out and main-in jacks by removing the Preamp-Out/Main-In Jumper Pins D and connecting the Preamp Out E jacks to the inputs of the external device, and the outputs of the device to the Main In C jacks. Alternatively, you may connect the external device to the Tape Monitor Loop. Connect the Tape Monitor Record/Out jacks 9 to the inputs of the external device, and connect the outputs of the device to the Tape Monitor Play/In jacks 8. Speaker and Output Connections Regardless of the brand of cable selected, we recommend that you use a cable constructed of fine, multistrand copper with an area of min. Cable with 1. 5 mm may be used for short runs of less than 3 meters. We do not recommend that you use cables with an area of 0. 8 mm2 or smaller due to the power loss and degradation in performance that will occur. 2 Questions about running cables inside walls should be referred to an installer or a licensed electrical contractor who is familiar with applicable local building codes in your area. 10 INSTALLATION AND CONNECTIONS Installation and Connections System and Power Connections The HK 3370 is designed for flexible use with external control components and power amplifiers. These connections are easy to make during an initial installation, or at a later date should you choose to upgrade your system. Remote Control Extension If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, an optional remote sensor may be used. Connect the output of the remote sensor to the Remote IR In jack 3. If other components are also prevented from receiving remote commands, only one sensor is needed. They may use this unit's sensor or a remote eye by running a connection from the Remote IR Out jack 4 to the Remote In jack on Harman Kardon or other compatible equipment. External Audio Power Amplifier Connections If desired, an optional, external amplifier may be used in place of the HK 3370's internal power amplifier. To connect an external power amplifier, first remove the Pre-Out/Main-In Jumper Pins D that connect the Preamp Out E and Main In C jacks on the rear panel. [. . . ] The Tape 2 page defaults to Harman Kardon CD-R control codes. The CD page defaults to Harman Kardon CD player or changer control codes. Please refer to the table below for specific information on the default functions of the affected keys for these devices. REMOTE BUTTON FUNCTIONS BUTTON PRESET DWN PRESET UP TUNING DWN U TUNING UP V Rec. /Pause ·/B Stop A Rev. Play G DISK SKIP Up DISK SKIP Down FM MODE PRESET SCAN TUNING Up D MEMORY AUTO PRESET CLEAR 1 2 3 4 5 6 7 8 9 0 ì ì ì ì ß oe î ø ¬ Ñ ° ° ° ° ° ° ° ° ° ° 1 2 3 4 5 6 7 8 9 0 INTRO SCAN TIME Display (Record Deck) INTRO SCAN (Play Deck)* CDP SELECT CDR SELECT PROGRAM FINALIZE CLEAR 1 2 3 4 5 6 7 8 9 0 CLEAR 1 2 3 4 5 6 7 8 9 00 0 PROGRAM INTRO SCAN TAPE MON Cassette deck control codes REV. [. . . ]