User manual HARMAN KARDON RCP 2

[. . . ] RCP 3 SYSTEM REMOTE OWNER'S MANUAL FOR USE WITH CP 40 SYSTEMS TABLE OF CONTENTS 3 4 8 9 10 11 11 11 11 12 13 15 15 16 17 17 18 18 18 INTRODUCTION AND FEATURES REMOTE CONTROL FUNCTIONS BATTERIES PROGRAMMING SOURCES USING EzSET ® ADVANCED FUNCTIONS Punch-Through Programming Macros Resetting the Remote APPENDIX Remote Control Function List Remote Control Product Codes TV VCR CD DVD SAT TAPE CBL 2 INTRODUCTION AND FEATURES Please register your product on our Web site at www. harmankardon. com. Note: You'll need the product's serial number. At the same time, you can choose to be notified about our new products and/or special promotions. WWW. HARMANKARDON. COM Thank you for choosing Harman Kardon®! Your CP Series system combines the superior performance and practical flexibility of high-quality separate audio/video components with the convenience of a complete system in one carton. You will need to provide a video display or television, but you may also add almost any source device, ranging from a cassette deck or VCR all the way up to the latest digital cable or satellite television set-top box, or even products that may be released in the future. The single RCP 3 remote replaces the original remotes supplied with the AVR 144 receiver and DVD 27 DVD player. [. . . ] A series of many fast flashes represents "0". Record the codes programmed for each device here. Table 1 ­ Remote Control Codes Source Input Video 1 Video 2 Video 3 DVD * CD Tape Product Type (circle one) VCR, PVR Cable, Satellite TV DVD CD, CDR Cassette Remote Control Code * Do not reprogram the DVD Source Selector unless you are replacing the DVD player included in the CP 40 system with another product. If you are unable to locate a code set that correctly operates your source device, it will not be possible to use the RCP 3 remote to control that device. However, you may still connect the source to the AVR 144 and operate it using the device's original remote control. Alternatively, you may wish to consider purchasing Harman Kardon's optional TC 30 activity-based remote, which is programmed by accessing a large database of product codes on the Internet. The TC 30 is also capable of "learning" codes from your device's original remote. However, the TC 30 is not equipped with the EzSet feature that automatically calibrates the system's speaker levels. Most of the button labels on the remote describe the button's function when used to control the AVR 144 (white or gray labels) or DVD 27 (blue labels). However, the button may perform a very different function when used to control another device. Refer to the Remote Control Function List, Table A1 in the Appendix, for a list of each button's functions with the various product types. If you wish, you may program Macros, which are preprogrammed code sequences that execute many code commands with a single button press. You may also program "punch-through" codes, which allow the remote to operate the volume, channel or transport controls of another device without having to switch the remote to the mode for that device. See page 11 for instructions on these advanced programming functions. NOTE: The RCP 3 remote is preprogrammed to operate the transport controls of the DVD 27 when the AVR or VID2 or VID3 device is selected. You may change this punch-through programming at any time, as explained in the Advanced Functions section. Figure 2 ­ Input Selectors 4. a) If the device turns off, then press the Input Selector again to accept the code, which will flash. b) If the device does not turn off, try entering another code. If you run out of codes, you may search through all of the codes in the remote's library for that product type by pressing the / or ¤ button repeatedly until the device turns off. When the device turns off, enter the code by pressing the Input Selector, which will flash. NOTE: When you enter a valid 3-digit code, the Program Indicator LED will change color to green. However, entering an invalid code changes the color of the LED to red. Once you have accepted a code, it's a good idea to try using some other functions to control the device. Sometimes manufacturers use the same Power code for several different models, while other 9 USING EzSET Using EzSet This section replaces Step Four in the Initial Setup section of the AVR 144 owner's guide. [. . . ] When the LED flashes amber, enter the code "333". When the green LED goes out, the remote will have been fully reset. 11 APPENDIX Refer to the numbered buttons in this drawing when using the Function List. Figure 4 ­ Remote Control Function List Reference 12 APPENDIX Table A1 ­ Remote Control Function List No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Button Name Power On Power Off Mute AVR DVD CD Tape VID 1 (VCR) VID 2 (CBL/SAT) VID 3 (TV) SPL AM/FM 6CH Sleep/CH+/Audio Test Tone T/V /V. OFF Vol Up Surr/CH­/Title OSD/Info Blank Vol Down / AVR Function Power On Power Off Mute AVR Select DVD Input Select CD Input Select Tape Input Select Video 1 Select Video 2 Select Video 3 Select EzSet Tuner Select 6/8 Ch. [. . . ]