User manual HARMAN KARDON RCP 4

[. . . ] RCP 4 SYSTEM REMOTE OWNER'S MANUAL (FOR USE WITH CP 45 SYSTEM) TABLE OF CONTENTS 3 4 9 10 12 13 13 13 14 15 16 18 18 19 20 20 21 21 21 INTRODUCTION AND FEATURES REMOTE CONTROL FUNCTIONS BATTERIES PROGRAMMING SOURCES LEARNING INDIVIDUAL KEY CODES ADVANCED FUNCTIONS Punch-Through Programming Macros Resetting the Remote APPENDIX Remote Control Function List Remote Control Product Codes TV VCR CD DVD SAT TAPE CBL 2 INTRODUCTION AND FEATURES Please register your product on our Web site at www. harmankardon. com. Note: You'll need the product's serial number. At the same time, you can choose to be notified about our new products and/or special promotions. WWW. HARMANKARDON. COM Thank you for choosing Harman Kardon®! Your CP Series system combines the superior performance and practical flexibility of high-quality separate audio/video components with the convenience of a complete system in one carton. You will need to provide a video display or television, but you may also add almost any source device, ranging from a cassette deck or VCR all the way up to the latest digital cable or satellite television set-top box (or even products that may be released in the future). The single RCP 4 remote replaces the original remotes supplied with the AVR 245 receiver and DVD 37 DVD player. [. . . ] This step places the remote in Program mode and varies slightly, depending on which Input Selector is being programmed. a) DVD, Tape, Video 1, Video 2, Video 3 and Video 4 Sources: Press and hold the Input Selector until the Program Indicator LED starts to flash, then release it. b) CD Source: Press the DVD/CD Input Selector twice quickly so that it turns green. Follow the directions in Step 4. 10 Figure 2 ­ Input Selectors c) HDMI 1 Source: Press and hold the Input Selector until the Program Indicator flashes, then release it. Next press the Input Selector that corresponds to the device type you want to program into the HDMI 1 mode, i. e. , DVD, VCR or CBL/SAT. d) HDMI 2 Source: Press and release the Input Selector once, quickly press the Input Selector again so that it turns green, then release it. Now press and hold the Input Selector until the Program Indicator flashes, then release it. Next press the Input Selector that corresponds to the device type you want to program into the HDMI 2 mode, i. e. , DVD, VCR or CBL/SAT. Then follow the directions in Step 4. 4. a) If the device turns off, then press the Input Selector again to accept the code; the selector will flash. b) If the device does not turn off, try entering another code. If you run out of codes, you may search through all of the codes in the remote's library for that product type by pressing the / or ¤ Button repeatedly until the device turns off. When the device turns off, enter the code by pressing the Input Selector, which will flash. NOTE: When you enter a valid three-digit code, the Program Indicator LED will change color to green. However, entering an invalid code changes the color of the LED to red. Once you have accepted a code, it's a good idea to try using some other functions to control the device. Sometimes manufacturers use the same power code for several different models, while other codes will vary. You may wish to repeat this process until you've programmed a satisfactory code set that operates most of the functions you frequently use. You may find out which code number you have programmed by pressing and holding the Input Selector to enter Program mode. Then press the Set Button, and the LED will flash in the code sequence. One flash represents "1", two flashes for "2" and so forth. A series of many fast flashes represents "0". [. . . ] Input Select Learn Channel + TV/VCR Volume Up The Bridge TM (DMP) XM HDMI 1/2 Power On Power Off Mute Power On Power Off Mute AVR Select DVD Input Select CD Input Select Mute (AVR) AVR Select DVD Select CD Select Tape Select HDMI 1 Select HDMI 2 Select VCR Select CBL/SAT Select TV Select Video 4 Select XM Select Tuner Select 6/8 Ch. Input Select Learn Mute AVR Select DVD Select CD Select Tape Select HDMI 1 Select HDMI 2 Select VCR Select CBL/SAT Select TV Select Video 4 Select XM Select Tuner Select 6/8 Ch. Input Select Learn Channel + TV/VCR Channel ­ OSD AVR Select DVD Select CD Select Tape Select HDMI 1 Select HDMI 2 Select VCR Select CBL/SAT Select TV Select Video 4 Select XM Select Tuner Select 6/8 Ch. Input Select Learn AVR Select DVD Select CD Select Tape Select AVR Select DVD Input Select CD Input Select Tape Select Bridge TM Tape Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Selectt 7 HDMI 1/HDMI 2 HDMI 1 Select HDMI 2 Select 8 VID 1 (VCR) 10 VID 3 (TV) 11 VID 4 12 XM 13 AM/FM 14 6/8CH 15 Learn 17 Test Tone 18 T/V/V. Off 19 Vol Up 20 Surr/Title 21 OSD/Info 23 Vol Down Volume Up* OSD Video 1 Select 9 VID 2 (CBL/SAT) Video 2 Select Video 4 Select XM Select Tuner Select 6/8 Ch. [. . . ]