User manual HARMAN KARDON RCP 5

[. . . ] RCP 5 SYSTEM REMOTE OWNER'S MANUAL (FOR USE WITH CP 55 SYSTEM) TABLE OF CONTENTS 3 4 8 9 11 12 12 12 13 14 15 17 17 18 19 19 20 20 20 INTRODUCTION AND FEATURES REMOTE CONTROL FUNCTIONS BATTERIES PROGRAMMING SOURCES USING EzSET® ADVANCED FUNCTIONS Punch-Through Programming Macros Resetting the Remote APPENDIX Remote Control Function List Remote Control Product Codes TV VCR CD DVD SAT TAPE CBL 2 INTRODUCTION AND FEATURES Please register your product on our Web site at www. harmankardon. com. Note: You'll need the product's serial number. At the same time, you can choose to be notified about our new products and/or special promotions. WWW. HARMANKARDON. COM Thank you for choosing Harman Kardon®! Your CP Series system combines the superior performance and practical flexibility of high-quality separate audio/video components with the convenience of a complete system in one carton. You will need to provide a video display or television, but you may also add almost any source device, ranging from a cassette deck or VCR all the way up to the latest high-definition digital cable or satellite television set-top box (or even products that may be released in the future). The single RCP 5 remote replaces the original remotes supplied with the AVR 146 receiver and DVD 38 DVD player. [. . . ] b) CD Source: Press the DVD/CD Input Selector twice quickly so that it turns green, then hold it until the selector relights and the Program LED flashes. Follow the directions in Step 4. 9 9 Figure 2 ­ Input Selectors c) HDMI 1 Source: Press and hold the Input Selector until the selector relights and the Program Indicator flashes, then release it. Next, press the Input Selector that corresponds to the device type you want to program into the HDMI 1 mode, i. e. , DVD, VCR or CBL/SAT. d) HDMI 2 Source: Press and release the Input Selector once, then quickly press the Input Selector again so that it turns green, then release it. Now press and hold the Input Selector until the selector relights and the Program Indicator flashes, then release it. Next, press the Input Selector that corresponds to the device type you want to program into the HDMI 2 mode, i. e. , DVD, VCR or CBL/SAT. Then follow the directions in Step 4. 4. a) If the device turns off, then press the Input Selector again to accept the code; the selector will flash. b) If the device does not turn off, try entering another code. If you run out of codes, you may search through all of the codes in the remote's library for that product type by pressing the / or ¤ Button repeatedly until the device turns off. When the device turns off, enter the code by pressing the Input Selector, which will flash. NOTE: When you enter a valid three-digit code, the Program Indicator LED will change color to green. However, entering an invalid code changes the color of the LED to red. Once you have accepted a code, it's a good idea to try using some other functions to control the device. Sometimes manufacturers use the same power code for several different models, while other codes will vary. You may wish to repeat this process until you've programmed a satisfactory code set that operates most of the functions you frequently use. You may find out which code number you have programmed by pressing and holding the Input Selector to enter Program mode. Then press the Set Button, and the LED will flash in the code sequence. One flash represents "1", two flashes for "2" and so forth. A series of many fast flashes represents "0". Record the codes programmed for each device in Table 1. PROGRAMMING SOURCES Table 1 ­ Remote Control Codes Source Input Video 1 Video 2 Video 3 HDMI 1 HDMI 2 DVD * CD Tape Product Type Remote Control Code (circle one) VCR, PVR Cable, Satellite TV DVD, VCR/PVR, Cable, Satellite DVD, VCR/PVR, Cable, Satellite DVD CD, CD-R Cassette * Do not reprogram the DVD Source selector unless you are replacing the DVD player included in the CP 55 system with another product. If you are unable to locate a code set that correctly operates your source device, it will not be possible to use the RCP 5 remote to control that device. However, you may still connect the source to the AVR 146 and operate it using the device's original remote control. [. . . ] Input Select Channel + Tuner Select 6 Ch. Input Select Channel + Tuner Select 6 Ch. Input Select Channel + Tuner Select 6 Ch. Input Select Channel + Tuner Select 6 Ch. [. . . ]