User manual HARMAN KARDON T45C

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. [. . . ] Press the Digital Input Select button on the remote. Within five seconds, make your input selection using the buttons on the remote until the desired digital or analog input is shown in the Main Information Display . Then press the OK button to enter the new digital input assignment. After the setting has been made with one input, repeat as described above with all inputs in use. The digital input associated with the input selected can also be changed at any time later and the AVR's memory system will keep the settings until they are changed again. 5. Turn the AVR on either by pressing the System Power Control or the Input Source Selector on the front panel, or via the remote by pressing the AVR Selector or any of the Input Selectors on the remote. The Power Indicator will turn blue to confirm that the unit is on, and the Main Information Display will also light up. NOTE: After pressing one of the Input Selector buttons to turn the unit on, press the AVR Selector to have the remote control the AVR functions. is selected, low frequency front When channel sounds will be sent only to the subwoofer output. Note that if you choose this option and there is no subwoofer connected, you will not hear any low frequency sounds from the front channels. This setting is not available with stereo mode to ensure purest sound by bypassing the crossovers of the DSP´s. When is selected, a full-range output will be sent to the front left and front right outputs. If the front left/right speakers are set to three options are available: , the , which is , Surround Setup Once the speaker setup has been completed, the next setup step is to set the surround mode you wish to use with each input. Since surround modes are a matter of personal taste, feel free to select any mode you wish ­ you may change it later. To make it easier to establish the initial parameters for the AVR, it is best to leave the default setting of Logic 7 Music mode for most analog inputs and Dolby Digital for inputs connected to digital sources. In the case of inputs such as a CD Player, Tape Deck or Tuner, you may wish to set the mode to Stereo, if that is your preferred listening mode for standard stereo sources, where it is unlikely that surround encoded material will be used. To set the surround mode you wish to use with the input selected, press the Surround Mode Selector button on the front or on the remote until the desired surround mode´s name appears in the Main Information Display . Note that Dolby Digital and DTS will only appear as choices when a digital input has been selected. After the surround mode setting has been made with the current input, repeat the setting with all inputs you will use. The surround mode can also be changed at any time later, and the AVR's memory system will keep the settings for the input selected, until they are changed again. If no subwoofer is connected to the AVR, press the arrow buttons so that appears in the display. When this option is selected, all bass information will be routed to the front left/right "main" speakers. If a subwoofer is connected to the AVR, you have the option to have the front left/right "main" speakers reproduce bass frequencies at all times, and have the subwoofer operate only when the AVR is being used with a digital source that contains a dedicated Low Frequency Effects, or LFE soundtrack. This allows you to use both your main and subwoofer speakers to take advantage of the special bass created for certain movies. [. . . ] After the pause, reconnect the AC power cord and check the unit's operation. If the system still malfunctions, a system reset may clear the problem. To clear the AVR's entire system memory including tuner presets, output level settings, delay times and speaker configuration data, first put the unit in Standby by pressing the System Power Control button . Next, press and hold the Surround Mode Button for 5 seconds. Note that once you have cleared the memory in this manner, it is necessary to re-establish all system configuration settings and tuner presets. NOTE: Resetting the processor will erase any configuration settings you have made for speakers, output levels, surround modes and digital input assignments as well as the tuner presets. [. . . ]