User manual HARMAN KARDON TD2 OWNERS GUIDE

[. . . ] The TD2 has been custom-designed to provide all the excitement and power of the cinema experience in your own living room. While sophisticated electronics and state-of-theart speaker components are hard at work within the TD2, hookup and operation are simple. Color-keyed cables and connections, and simple controls make the TD2 easy to use. To obtain maximum enjoyment from your new home theater speaker system, we urge you to take a few minutes to read through this manual. [. . . ] It doesn't matter which satellite speaker is used for any of the front or rear positions. (The center speaker and powered subwoofer are already color-coded for you. ) Speaker Position Sticker (or Terminal) and Cable Color Center Channel Speaker Green 0-0, 55 m 1, 5-1, 85 m White Red Front Left Front Right Center Surround Left Surround Right Subwoofer (LFE) White Red Green Blue Gray Purple The center channel speaker should be placed slightly behind the front left and right speakers, and no more than two feet above or below the tweeters of the left and right speakers. It is often convenient to set the center speaker on top of the television set, as shown in the drawing. The two surround speakers should be placed slightly behind the listening position and, ideally, should face each other and be at a level higher than the listeners' ears. If that is not possible, they may be placed on a wall behind the listening position, facing forward. The surround speakers should not call attention to themselves. Experiment with their placement until you hear a diffuse, ambient sound accompanying the mainprogram material heard in the front speakers. Subwoofer White Red Purple Satellites and Surrounds Front Speakers White Red The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listeners' ears will be, or they may be angled toward the listeners. The low-frequency material reproduced by the subwoofer is mostly omnidirectional, and this speaker may be placed in a convenient location in the room. However, the best reproduction of bass will be heard when the subwoofer is placed in a corner along the same wall as the front speakers. Experiment with subwoofer placement by temporarily placing the subwoofer in the listening position and moving around the room until the bass reproduction is best. Place the subwoofer in that location. The satellite speakers may be placed on a shelf. Surround Speakers White Green Red They may be wall-mounted using the supplied brackets. Blue Gray 6 SPEAKER PLACEMENT Mounting Options Wall-Mounting for Satellites Unscrew the bolt that attaches the black shelf stand to the bottom of the speaker. Store the stand and bolt in a safe place in case they are needed for a future installation. Although the TD2 system has red and black collars on the individual speaker terminals to denote the positive and negative connections, your system includes a colored band on the positive lead at both ends of every speaker cable and a matching colored sticker for each of the four satellite speakers, conforming to the key on page 6. The center speaker has a green (+) terminal, and the subwoofer has a purple SUB input jack. This system is intended to help you ensure that the speaker in each location is connected to the correct terminals on your receiver or amplifier. The (+) lead of the speaker wire is indicated with a stripe and has the colored band corresponding to the speaker's position. It is important to connect all speakers identically: (+) on the speaker to (+) on the amplifier and (­) on the speaker to (­) on the amplifier. Wiring "out of phase" results in thin sound, weak bass and a poor stereo image. 8 SPEAKER CONNECTIONS Speaker Connections Dolby Digital or DTS® (or Other Digital Surround Mode) Connection Use this installation method for Dolby Digital, DTS® or other digital surround processors: Use the line-level input jack marked "SUB" for the Low-Frequency Effects channel. Connect this jack to the LFE output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround-sound processor for "Subwoofer On. " The front left, front right, center and rear speakers should all be set to "Small. " ENGLISH Front Left ­ + Center ­ + Front Right ­ + SUB-TS11 Subwoofer LINE LEVEL IN SUB R L Front Left SUB/LFE Out Surround Left Center Front Right Surround Right Surround Left ­ + Receiver Surround Right ­ + SPEAKER CONNECTIONS 9 Speaker Connections Dolby Pro Logic (Non-Digital) ­ Line Level Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS® or other digital processing), where the receiver/processor is equipped with a subwoofer output, or a volume-controlled preamp (line-) level output: Use RCA-type patch cords to connect the linelevel subwoofer output on your receiver or to amplifier either the left or right line-level input on the subwoofer. Use both the left and right inputs on the subwoofer if your receiver or processor has both left and right line-level outputs. In that case, you will need to supply a second interconnect cable. [. . . ] · Check all wires and connections between receiver/amplifier and speakers. Make sure none of the speaker wires are frayed, cut or punctured. · Review proper operation of your receiver/amplifier. · Check the "Balance" control on your receiver/amplifier. [. . . ]