User manual HARMAN KARDON TD4800

[. . . ] Otherwise, please visit the product support section of our Web site at www. harmankardon. com for information on upgrading your receiver. The TD4800 has a wide range of features and options that accommodate virtually any combination of speakers, room size and program sources. It is as easy to operate as it is to set up, but in order to take maximum advantage of the many advanced technologies within your new AVR, it is strongly recommended that you take a few minutes to read this owner's manual. If you have any questions about this product, its installation or its operation, we recommend that you contact your dealer or installer, as they are your best source of local information. [. . . ] Press the / Navigation Button o once to 33 26 25 37 change the bottom line of the remote's LCD display 32 to read MANUAL SPL as shown 27Figure 14. in 24 36 31 28 23 35 SET SPKR LEVELS 30 29 22 34 MANUAL SPL 29 30 21 33 Figure 14 28 31 20 32 3. Press the Set Button q within five seconds to activate the remote's manual mode, so that it functions as an SPL meter. The right corner of the bottom line of the remote's display will show the output level of the speakers as the test tone circulates. The level will show as a direct SPL indication between 66dB and 79dB. Below 66dB the remote will read LOW and above 79dB it will read HIGH. When you are finished with all adjustments, press the Clear Button 9 to return the remote to normal operation. NOTE: The subwoofer level is not adjustable when the normal test tone is in use. The subwoofer output level may be adjusted when the channel levels are being trimmed to a program source rather than the test tone, as shown on page 35. When all channels have an equal volume level, the adjustment is complete. To exit this menu, press the //¤ Navigation Button o until the on-screen cursor is next to the BACK TO MASTER MENU line, and then press the Set Button q to return to the MASTER MENU. The unit may also be turned on from Standby by pressing any of the Input Selector Buttons dXhç on the remote or the Input Source Selector Button 7 on the front panel. Whenever the AVR is turned on, you will see all of the front-panel indicators light up for a few seconds. This is normal, and it is part of the unit's power-on self test procedure. NOTE: After pressing one of the Input Selector Buttons dXhç to turn the unit on, press the AVR Selector e to set the remote control to the TD4800 functions. To turn the unit off at the end of a listening session, simply press the Standby/On Switch 1 on the front panel or the Power Off Button aå on the remote. Power will be shut off to any equipment plugged into the rear-panel Switched AC Accessory Outlet / and the illumination around the Standby/ On Switch 1 will turn amber. When the remote is used to turn the unit "off, " it is actually placing the system in a Standby mode, as indicated by the amber lighting around the Standby/On Switch 1. · To program the TD4800 for automatic turn-off, press the Sleep Button S on the remote. Each press of the button will decrease the time before shut-down in the following sequence: 49 47 and hold the Sleep ButtonS until the information 45 48 display returns to normal brightness; the Sleep 46 44 35 indicator numbers will disappear and the words 37 39 34 36 SLEEP OFF will appear in the Lower Display 38 33 26 25 Line $. 43 6-Channel/8-Channel Direct Input 42 There are two input choices available for use with · 41 sources such as a DVD-Audio or SACD player 37 connected to 40 that are 41 47 51 the 8-Channel Direct 36 46 50 37 Inputs 40 . Select the appropriate input according 35 39 45 49 32 27 24 36 to the way your system and source equipment is When you will be away from home for an extended 31 28 34 38 configured: 44 48 period of time, it is always a good idea to completely 23 35 30 29 22 34 33 43 turn the unit off with the front-panel Main Power 29 30 21 33 I The 6 CH DIRECT input should be used 32 42 Switch A. [. . . ] When the remote has been totally reset and returned to the factory default condition, a REMOTE RESET COMPLETE message will appear (Figure 79) briefly, and then the remote will return to normal operation. REMOTE RESET COMPLETE · The remote has a built-in backlight that may be activated by pressing the Light Button P. This button is made from a special "glow" material so that it is easier to find in dark rooms. This glow feature does not consume any electricity, but the glow will fade when the remote is kept in a dark location for an extended period of time. The "glow" feature may be restored by placing the remote in normal room light for a few hours. [. . . ]