User manual HASBRO LINCOLN LOGS GENERAL STORE

[. . . ] 3 Press the ASSIST button to display the Recovery, Backup and Troubleshooting Guide Recovery is the process of restoring the built-in hard disk drive or SSD back to its original factory condition. Refresh is the process of reinstalling the operating system with the main settings and personal data retained. There are two ways to recover your computer:  From Recovery Media  From the recovery area The 64 GB or 128 GB SSD equipped models do not support the refresh function. If you check the capacity of the SSD, press the ASSIST button while your computer is off to display the VAIO Care Rescue Mode screen, and select Start BIOS setup. VAIO Care Rescue Mode screen and select Start from media (USB device/ optical disc). [. . . ] Follow the on-screen instructions until the Choose an option screen appears. 3 Select Troubleshoot and Recovery and 2 Select Recover or maintain your system. 3 Select Troubleshoot and Refresh your PC. maintenance. Follow the on-screen instructions until the VAIO Care (Rescue Mode) : Recover or maintain your system screen appears. If the display language selection window appears, select your desired language and OK. Why do I have to back up my data? Due to unexpected events or computer viruses, you might lose various data stored on the built-in hard disk drive or SSD. To restore the lost data, its backup copy is needed. It is strongly recommended that you back up your data regularly. 5 Select Start recovery wizard. 6 Follow the on-screen instructions. To perform the custom recovery, select Tools and Start advanced recovery wizard. If you cannot recover your computer using the USB flash drive, connect the drive to another USB port on the computer and try recovering the computer again. When do I have to perform recovery or refresh?  If your computer has become unstable  If your computer has been infected with a computer virus  If your computer is experiencing problems which cannot be solved through troubleshooting  If you have formatted the C: drive by mistake For details, refer to the on-screen User Guide. Copyright protected data, such as digital broadcast data or music files organized by digital media playback apps, may not be available, even if the data is retained in the same location after you refresh your computer. Refer to the help file included with the app you are using for instructions. The apps installed at the time of delivery and installed from Windows Store are retained, whereas all Desktop apps that you installed after the purchase will be erased. 4 Select Start recovery wizard.  Make sure the battery pack is installed properly and charged.  Disconnect all cables and peripheral devices, such as the power cord, the AC adapter, and the USB device, remove the battery pack, and wait about five minutes. Then, put them back in place and turn on your computer again.  Remove all extra memory modules you may have installed since purchase, and then restart your computer.  If your computer is plugged into a power strip with a switch, make sure the switch is turned on and the power strip is securely plugged into a power source.  If you are using an external display, make sure it is plugged into a power source and turned on. close the app window.  Press the Ctrl+Alt+Delete keys, select (Shut down) in the lower right corner of the computer screen, and then select Restart.  Press and hold the power button or slide and hold the power switch for more than four seconds to shut down your computer. Unplug the power cord or the AC adapter, and leave the computer for about five minutes. Then plug the power cord or the AC adapter, and turn on the computer again. Turning off your computer with the Ctrl+Alt+Delete keys, the power switch, or the power button may cause loss of unsaved data. A message appears notifying of either incompatibility or improper installation of the battery pack and my computer then enters Hibernate mode See the answers for "The charge indicator light is blinking fast and my computer does not start. " How can I create a hard disk partition? If you reduce the volume of the C: drive partition, you may not create Recovery Media or complete the recovery process and refresh process successfully because the free space on the built-in hard disk drive or SSD is not sufficient. Windows does not accept my password and returns the message: Enter Onetime Password If you enter a wrong power-on password three times consecutively, the Enter Onetime Password message appears and Windows will not start. [. . . ] If the User Account Control window appears, select Yes. Volume. 2 Right-click the C: drive and select Shrink 3 Enter the size of the partition to be created in Enter the amount of space to shrink in MB and select Shrink. 4 Right-click Unallocated and select New Simple Volume. The charge indicator light is blinking fast and my computer does not start  This problem could be due to the battery I cannot remember the power-on password If you have forgotten the power-on password, contact an authorized Sony service/support center. A reset fee will be charged. 5 Follow the on-screen instructions. The Activate Windows screen appears The Windows activation is not completed. Select Go to PC settings and connect your computer to the Internet, and then the activation automatically starts. [. . . ]