User manual HASBRO MICRO MACHINES RAGING INFERNO CITY

[. . . ] Also make certain the outlet is properly grounded. q For the power supply requirements, see the name plate of the main unit. 3. Do not install your machine in areas that are: damp, humid, or very dusty q exposed to direct sunlight q poorly ventilated q subject to extreme temperature or humidity changes, e. g. , near an air conditioner or heater. q 4. Be sure to allow the required space around the machine for servicing and proper ventilation. A small amount of ozone is produced within the copier 23-5/8" (60cm) 11-13/16" (30cm) 23-5/8" (60cm) 23-5/8" (60cm) during operation. [. . . ] When using the operation panel on the main unit, select the desired symbol set item and register it. When using the operation panel with touch panel, select the number that corresponds to the desired symbol set and register it. PostScript settings This setting specifies whether the cause of an error is printed or not when a PostScript error has occurred. Default setting: Not print Print or not print can be selected concerning the cause of a PS (PostScript) error. 3-4 CUSTOM SETTINGS Custom settings are used for various settings based on the customer operating conditions. The items that can be set with the custom settings are shown below. G Total count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The number of printed pages and the like are displayed. (See page xxxx. ) G Display contrast*1 . . . . . . . . . . . . . . . . . . . . . . . . . . . The display contrast of the operation panel is adjusted. (See page xxxx. ) G List print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Used to print a list of settings that have been made or a font list. (See page xxxx. ) G Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Depending on the setting item, additional item selection and registration operation may be needed. In this case, use the or key to select an item and press the [OK] key to register it. To set another item, press the [BACK/C] key and repeat steps 5 and 6. 7 When setting is complete, press the [MENU] key to return to the basic screen. NOTE If the [BACK/C] key is pressed after each setting is complete, the display that has called the setting will appear again. If selection of a number is mistaken during setting operation, press the [BACK/ C] key to correct the selected number. When using the operation panel with touch panel: 1 Press the [CUSTOM SETTINGS] key when the printer screen is displayed to display the custom settings menu screen. Any print jobs held in the printer and any job currently transmitted to the printer will be printed in the former custom setting conditions. 3 Touch the desired setting on the setting screen of the desired item and touch the [OK] key. CUSTOM SETTINGS TRAY SETTINGS TYPE / SIZE TRAY 1 TRAY 2 TRAY 3 PLAIN / 8 X11 PLAIN / AUTO-INCH RECYCLED / AUTO-INCH 1 / 2 OK PRINT COPY FAX 1/2 2 Touch the key of the desired item to display its setting screen. To set another item, repeat steps 2 and 3. CUSTOM SETTINGS TOTAL COUNT TRAY SETTINGS DISPLAY ADDRESS LIST PRINT RECEIVE MODE CLOCK FAX DATA 4 To finish the setting operation, touch the [EXIT] key. KEY OPERATOR PROGRAMS For details of each setting item, see the description on and after the next page. CUSTOM SETTINGS TRAY SETTINGS TYPE / SIZE TRAY 1 TRAY 2 TRAY 3 PLAIN / 8 X11 PLAIN / AUTO-INCH RECYCLED / AUTO-INCH 1 / 2 OK PRINT COPY FAX 1/2 Depending on the setting item, additional item setting keys may be displayed and page switching keys may be displayed. If a check box is displayed for an item, the item can be set by touching the key to display a check mark ( ) in the box. 3-6 CUSTOM SETTINGS Setting items I Total count The number of total printed pages in this product can be displayed and printed. The displayed or printed items vary with installation of peripheral units. I Tray settings Paper type, paper size, operation mode, and use of automatic tray switching are set for each tray. The operation mode can be set when this product is equipped with a scanner module as a peripheral unit. If the product is not equipped with a scanner module, use the item “Auto tray switching” described below for setting the automatic tray switching function. I Display contrast Can be set if this product is equipped with a scanner module as a peripheral unit. This item is used to adjust the contrast of the touch panel display. I Auto tray switching This item can be set if this product is not equipped with a scanner module as a peripheral unit. If the auto tray switching function is set and more than one tray of the same paper size is installed in this product, printing can be continued by switching automatically the paper tray when paper of a tray runs out. This item is used to enable the auto tray switching function. [. . . ] When the operation panel with touch panel is used, execution of the program can be canceled by touching the [CANCEL] or [NO] key. System settings (product key) Use these programs to perform product key (password) input operation in the following cases. G To use this product as a PostScript compatible printer The password to be entered is described in the operation manual supplied with the optional PS3 expansion kit. G To use the network scanner feature (only if the operation panel with touch panel is used) The password to be entered is described in the operation manual supplied with the network scanner expansion kit (peripheral unit). *1 Restore factory defaults This program is used to reset the settings of the configuration settings (page xx) and the system settings (default settings/interface settings) of the key operator programs (pages xx to xx) to the factory default settings. If you wish to record the settings before resetting, use "List Print" of custom settings to print the settings before using this program. NOTE After this program is set, exit the key operator program, turn off the main switch, and then turn on the main switch again after a while. [. . . ]