User manual HASBRO OMEGA VIRUS

[. . . ] – The air extraction system must not exceed the specified pressure losses, see page 3. – Only use materials and parts specified in the instructions. – Clean the exhaust air duct regularly, at least once a year. When operating the dryer without an exhaust air duct, the following must also be observed: – Ensure that the room is well ventilated, otherwise energy consumption and drying time will increase. [. . . ] Remove the cover on the side panel. Example: pipe connection - inside diameter = 100 mm, smooth A = straight piece (1. 0 m) 4 B = curved pipe (R = 200 mm) 4 C = straight piece (1. 5 m) 6 D = pipe elbow 19 E = telescopic wall box with grid 14 Total pressure loss 47 2. Remove the bayonet ring from the back panel and attach it to the opening on the side panel. 2. Seal the opening in the back panel with the cover. Installation for pipe connection - inside diameter = 100 mm In order to ensure the minimum required air flow, a certain pressure loss (resistance) must not be exceeded. The permissible total pressure loss in an exhaust air duct must not exceed a certain value. This is calculated as the sum of all individual pressure loss values for the straight pieces and fixtures in the exhaust air duct. The value for the maximum permissible total pressure loss for an exhaust air duct is 50*. Route the exhaust air directly into the open air via an exhaust air pipe through an open window. Example: Pipe connection - inside diameater = 100 mm, flexible pipe, corrugated A = curved pipe (R = 300 mm) 7 B = straight piece (1. 5 m) 18 C = curved pipe (R = 100 mm) 10 D = straight piece (0. 5 m) 6 Total pressure loss 41 3. Through a wall box into chimneys or ventilation shafts – It is not permitted to connect the exhaust air duct to chimneys which are connected to gas or coal-fired ovens/cookers or gas-fired heating systems. – If the appliance is being connected to a moisture-insulated ventilation shaft the responsible chimney sweep must be informed and the approval of the local building department (building supervision office) or the owner of the building must be obtained. – If other appliances are operated in the room where the appliance is installed or in adjoining rooms, e. g. gas-fired heating systems, gas-fired boilers, coal-fired ovens connected to a chimney, or open fireplaces, a vacuum may be created, leading risk of poisoning. – Only use materials and parts specified in the instructions. – Clean the exhaust air duct regularly, at least once a year. When operating the dryer without an exhaust air duct, the following must also be observed: – Ensure that the room is well ventilated, otherwise energy consumption and drying time will increase. to walls, – Ensure that the room is well ventilated furniture. – Do not cover the exhaust air opening (leave approx. 1 m of free space around the exhaust air opening). 2. Remove the cover on the side panel. 2. Remove the bayonet ring from the back panel and attach it to the opening on the side panel. 3. Seal the opening in the back panel with the cover. Condensation outlet If there is a high level of condensation in the exhaust air duct, it is advisable to fix a condensation collector (standard) or a drain hole with a diameter of approximately 3 mm to the lowest part of the exhaust air duct. 1 2 Notes on installation Exhaust air duct All standard products can be used for the exhaust air duct: – flexible pipes – galvanised metal ducts or pipes – connectors, adapters, and diverters for flat duct systems and pipe systems – wall boxes for evaporation into the open air or into a ventilation shaft – adapters on rectangular ducts – rectangular ducts or plastic pipes – backpressure flap The material must be heat resistant up to 80 °C and moisture resistant. Installation options – Route the exhaust air duct in such a way that the dryer cannot draw the moist, warm exhaust air back in again. – The outlet for the exhaust air must be designed or positioned in such a way as to prevent any additional backpressure (e. g. from a direct ingress of wind) on the escaping exhaust air, e. g. [. . . ] diverters (bends, elbows, angles), wall boxes with grids or backpressure flaps. Example: pipe connection - inside diameter = 100 mm, smooth A = straight piece (1. 0 m) 4 B = curved pipe (R = 200 mm) 4 C = straight piece (1. 5 m) 6 D = pipe elbow 19 E = telescopic wall box with grid 14 Total pressure loss 47 2. Directly into the open air Installation for pipe connection - inside diameter = 100 mm In order to ensure the minimum required air flow, a certain pressure loss (resistance) must not be exceeded. The permissible total pressure loss in an exhaust air duct must not exceed a certain value. This is calculated as the sum of all individual pressure loss values for the straight pieces and fixtures in the exhaust air duct. [. . . ]