User manual HASBRO POLE POSITION

[. . . ] 5 Installing and removing the filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Replacing bulbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pipe dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] from the glare of an LED in risk group 1. Do not look directly into the LED light for longer than 100 seconds while it is switched on. 3 Cleaning and care Risk of burns, risk of electric shock!Always leave appliance to cool down before cleaning or servicing. Caution! ■ Maintenance and repair Risk of fire, risk of injury!Switch off the fuse or pull out the mains plug. Repairs may be performed by a qualified technician (electrician) only. Switch off the fuse or pull out the mains plug and call customer service. A damaged connection cable must be replaced by a qualified technician (electrician). Switch off the fuse or pull out the mains plug. Always replace defective bulbs immediately (leave bulbs to cool down first) to prevent the remaining bulbs from overloading. Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth. Take the metal mesh grease filter out of the holder. Grease can accumulate in the bottom of the metal mesh grease filter. – Do not hold the metal mesh grease filter at an angle, otherwise grease will drip out. Installing the metal mesh grease filter 1. Insert the metal mesh grease filter. While doing this, place the other hand under the metal mesh grease filter. 2. Fold up the metal mesh grease filter, locking it in place. 5 Cleaning and care : Risk of burns, risk of electric shock! from appliance. Always leave appliance to cool down before cleaning or servicing. Caution! ■ Cleaning the metal mesh grease filters The inserted metal mesh grease filters absorb the grease particles from the kitchen fumes. Clean the metal mesh grease filters under normal use (1 to 2 hours daily) approx. Notes ■ Do not use any aggressive, acidic or alkaline cleaning agents. ■ Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth. Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the grain direction only. Do not use any stainless steel cleaners for operator controls. [. . . ] Screw in threaded pin, leaving it protruding out of the wall by 1. Press the safety caps with the arrow upwards onto the 5 - 9 mm. . ª brackets until they engage. Screw on the knurled nut and washer firmly. ¯ ) & * Attaching and aligning the appliance 1. [. . . ]