User manual HASBRO PUZZ 3D R2D2

[. . . ] IG-CL5U will stop operating after about 26 months (9, 000 hours) if the Plasmacluster Ion Generating Unit is not replaced. declaration of Conformity Plasmacluster Ion Generator PUZZ 3D R2D2 This device complies with Part 8 of FCC rules. Responsible Party: HASBRO ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07495-63 Declaration of Conformity Plasmacluster Ion Generator PUZZ 3D R2D2 This ISM device complies with Canadian ICES-00 Responsible Party: HASBRO ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga , Ontario L4Z W9 Canada TEL: (905) 568-740 • REPLACEMENT OF PLASMACLUSTER ION GENERATING UNIT . [. . . ] (c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to head cleaning tapes and chemical cleaning agents. (d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons, cables and paper. (e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear. (f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or liquid spillage. (g) Any product received without appropriate model, serial number and CSA/cUL markings. Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television with the screen size of 27” or larger and on any Sharp Over-the-Range Microwave Oven. This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. €¢ This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. €¢ Children should be supervised to ensure that they do not play with the appliance. CAUTIONS CONCERNING OPERATION: • DO NOT sit on the main unit and do not lean on it, it may cause injury or malfunction. • DO NOT block the air intake and/or air outlet. €¢ DO NOT use the unit near or on hot objects, such as stoves or heaters or where it may come into contact with steam. €¢ Always operate the main unit in an upright position. €¢ Clean the exterior with a soft cloth only, otherwise the main unit surface may be damaged or cracked. €¢ Keep the main unit away from water. INSTALLATION GUIDELINES: • Avoid using in locations where the unit is exposed to condensation or drastic temperature changes. Appropriate room temperature is between 32-95ºF(0-35ºC). €¢ Avoid locations where grease or oily smoke is generated, otherwise the main unit surface may crack as a result. [. . . ] 13 8:58:16 AM REPLACEMENT OF PLASMACLUSTER ION GENERATING UNIT Plasmacluster Ion Generating Unit Model IZ-CCL5U * Before replacing the Plasmacluster Ion Generating Unit, be sure to turn off the main unit, unplug the power cord, and never handle the plug with wet hands. 2 Remove the screw by using a coin with a similar-size coin head or a screwdriver, and the Plasmacluster lon Generating Unit. cleaning Brush Plasmacluster Ion Generating Unit. * After replacing the Plasmacluster Ion Generating Unit, fill the replacement date on the Date Label at the side of the main unit. [. . . ]