User manual HASBRO SONNY THE SEAL

[. . . ] Connecting the water inlet hose • To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection. To a suitable hot water connection point: your dishwasher may be provided with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. • Positioning and levelling 1. [. . . ] Loading the detergent A successful wash also depends on the correct amount of detergent being used, as recommended by the manufacturer. Exceeding the recommended amount does not result in a more effective wash and pollutes the environment. Only use detergent which has been specifically designed for dishwashers. The use of tablets is only recommended for models which offer the MULTI-FUNCTIONAL TABLETS option. To obtain the best results from each washing and drying cycle, powder detergent, rinse aid liquid and salt should be used. Pour in the detergent after consulting the Wash cycle table: • for powder detergent use compartments A and B • for tablets, when the cycle requires 1 tablet, place it in compartment A and close the cover; when it requires 2, place C the second tablet at the bottom of the appliance. Remove detergent residues from the edges of the compartment and close the cover until it clicks. Modifying a wash cycle in progress If a mistake was made during the wash cycle selection process it is possible to change the cycle, provided that it has only just begun: turn the SELECT WASH CYCLE knob in an anticlockwise direction until it reaches the RESET position. After a few seconds, 4 beeps will sound and the WASH CYCLE PHASE indicator light will switch off, indicating that all settings have been cancelled. Washing options Extra drying* To make sure that the crockery is completely dry at the end of the cycle, press the EXTRA DRYING button before selecting the wash cycle. A prolonged beep will sound to indicate that this option has been selected and a short beep will sound to indicate when it has been deselected. G NEVER pour the rinse aid directly into the appliance tub. Adjusting the amount of salt* It is possible to adjust the amount of salt used according to the hardness of the water in your area (this information is available from your local water board). Turn the arrow on the neck of the dispenser (see figure) towards the + or symbols, using the table below as a guide. Adjusting the amount of rinse aid If you are not completely satisfied with the washing or drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are bluish streaks on the crockery, set the adjuster to a lower number (1-3). €¢ if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). If you are using multi-functional tablets and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. 9 Selector knob position / MED + Salt consumption (grams/cycle) 0 20 40 60 Autonomy (cycles/2 kg) / 60 40 25 Loading the refined salt In order to obtain the best possible results from a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery. The salt dispenser is located in the lower part of the dishwasher (see Description) and should be filled: • when the green float* cannot be seen by simply looking at the cap of the salt dispenser; • when the LOW SALT* indicator light on the panel flashes; • if your machine is not equipped with an indicator light or a The default setting of the water softening system is +. - If using multi-functional tablets fill the salt dispenser and set the adjuster to -; if the hardness of the water is greater than 60°fH, set it to +. [. . . ] problem: The dishwasher does not start. €¢ • • • • • • • EN Possible causes / Solutions: • The plu g h as n ot be en inserted into the electrical socket prop erly, or there is no p ow er in the ho use. T h e le v el of the r e fin e d s alt is low or th e do s a g e s ettin g is n o t s uite d to the hard ness of the w ater (see R inse aid and salt). t h e lid o n th e s a lt d is pe ns e r is n ot c los ed p r op erly. [. . . ]