User manual HASBRO SPIDER-MAN ELECTRONIC LCD VIDEO GAME

[. . . ] Connecting the water inlet hose • To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection. • To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance). [. . . ] The number and type of wash cycles and options may vary depending on the dishwasher model. For available OPTIONS please refer to the Table of options on the Start-up and use page. Pre-wash for dishes while awaiting completion of the load with the dishes from the next meal. Environmentally-friendly wash cycle with low energy consumption levels, suitable for pans and dishes. Economic and fast wash to be used for lightly soiled dishes. (Run cycle immediately after use) (2 plates + 2 glasses + 4 pieces of cutlery + 1 saucepan + 1 small frying pan). Economic and fast wash for delicate items which are sensitive to high temperatures. (Run cycle immediately after use) (glasses upper rack+ delicate plates, lower rack). It is ideal for night-time operation of the appliance. Good Night 21 g (A) 4 g (B) 21 ml (A) 4 ml (B) 1 (A) Yes A-C 3:30’ Notes: Optimum performance levels when using the "Speed 25’ wash" cycles can be achieved by observing the maximum amounts of crockery specified. To make it easier to measure out the detergent, it is worth remembering that: 1 tablespoon = 15 gr. Use a screwdriver to turn the dosage adjuster (F) to one of the 6 pre-set positions (the default position is set to 4): • If there are streaks on the crockery, set the adjustment device to a lower number (1-3). • If drops of water remain on the crockery or if there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). Setting the water hardness Every dishwasher is equipped with a water softener which, by using refined salt designed especially for this type of appliance, supplies water without limescale which is then used to wash the crockery. This dishwasher offers a setting which helps to reduce pollution and optimises washing performance in accordance with the water hardness level in your area. This information can be obtained from your local water supplier. - Switch on the appliance by pressing the ON/OFF button. - Press the P button and hold for approximately 5 seconds; two short beeps will sound, the text H2O will appear on the display and the set hardness number will flash (the water softening system is set by default to number 3). Press the P In order to achieve the best possible results using a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery. The salt dispenser is located in the lower part of the dishwasher (see Description) and should be filled: • When the green float* cannot be seen by simply looking at the cap of the salt dispenser. • When the LOW SALT* indicator light on the control panel/ display is illuminated; 1. [. . . ] malfunction: The dishwasher does not start. Possible causes / Solutions: • Th e p l u g h a s n o t b e e n i n s e r t e d i n t o t h e e l e c t r i c a l s o c k e t p r o p e r l y , o r there is no power in the house. € A n e xc es s ive am ou nt of foa m has been produc e d: the d et erg ent has not been m easured out correctly or it is not suitable for use in dishwashers (see Start-up and use). € Th e l e v e l o f t h e r e f i n e d s a l t i s l o w o r t h e d o s a g e s e t t i n g i s n o t s u i t e d t o the hardness of the wate r (see Rinse aid and s alt). [. . . ]