User manual HASBRO SPIROGRAPH COLOR CHANGE

[. . . ] c ontr olla r e c he il filtro entr a ta ac q u a n on s i a intas ato da i mp urità. • To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance). [. . . ] Economic and fast wash to be used for lightly soiled dishes. (Run cycle immediately after use) (2 plates + 2 glasses + 4 pieces of cutlery + 1 saucepan + 1 small frying pan). Economic and fast wash for delicate items which are sensitive to high temperatures. (Run cycle immediately after use) (glasses on the upper rack + delicate plates, on the lower rack). Auto Normal 29 g (A) 6 g (B) 29 ml (A) 6 ml (B) 1 (A) Yes A–B–C 1:45’ 25 g (A) Daily A 60 25 ml (A) 1 (A) No A–B– C 1:00’ No Soak No No No A–B 0:08’ Eco*50°C 29 g (A) 6 g (B) 29 ml (A) 6 ml (B) 1 (A) Yes A–B-C 2:45’ 25 g (A) 25 ml (A) 1 (A) No A -C 0:25’ 35 g (A) Crystal 35 ml (A) 1 (A) Yes A– B–C 1:30’ Notes: Optimum performance levels when using the "Daily wash" and "Speed wash" cycles can be achieved by observing the maximum amounts of crockery specified. To make it easier to measure out the detergent, it is worth remembering that: 1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. Of powder = approximately 5 ml of liquid * The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less energy and is les harmful to the environment. Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following address: ASSISTENZA_EN_LVS@indesitcompany. Com 20 Rinse aid and refined salt Only use products which have been specifically designed for dishwashers. • When the LOW SALT* indicator light on the control panel is illuminated; 1. Remove the lower rack and unscrew the container cap (anticlockwise). The first time you do this: fill the water tank right up to its edge. Position the funnel* (see figure) and fill the salt container right up to its edge (this should hold approximately 1 kg); it is not unusual for a little water to leak out. Remove the funnel* and wipe any salt residue away from the opening; rinse the cap under running water and then screw it on, the head facing downwards so as to let the water flow out of the four cracks which are arranged in a star shape on the lower part of the cap. (Salt cap with green float*) It is advisable to perform this procedure every time you add salt to the container. Make sure the cap is screwed on tightly, so that no detergent can get into the container during the wash cycle (this could damage the water softener beyond repair). When necessary, measure out the salt before a wash cycle so that any saline solution which has leaked out of the salt dispenser is removed. Adjusting the amount of rinse aid If you are not completely satisfied with the drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster (F) to one of the 6 pre-set positions (the default position is set to 4): • If there are streaks on the crockery, set the adjustment device to a lower number (1-3). • If drops of water remain on the crockery or if there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). [. . . ] The rins e aid has been used up or the dosage is too low. The crockery is m ade from non-stick m aterial. a was h cycle without a drying program m e has been selected. The rins e aid has been used up or the dosage is too low (see Rinse aid and salt). [. . . ]