User manual HASBRO WALK ALONG SESAME STREET

[. . . ] Pour en tirer le meilleur parti, veuillez lire ce mode d'emploi très attentivement. Muchas gracias por haber adquirido este producto HASBRO. Lea atentamente este manual para conseguir el mejor rendimiento del aparato. Le servirá también como guía operativa de este producto HASBRO. [. . . ] For example, to choose 30 1 Press the "+10" button three times. 2 Press the "0" button. To cancel random play: Press the / ( / ) button. "NORMAL" will appear for 2 seconds. E-15 04/1/28 GX-CD5100V_EN1. fm WALK ALONG SESAME STREET Notes: If you press the button during random play, you can move to the track selected next by the random operation. On the other hand, the button does not allow you to move to the previous track. The beginning of the track being played will be located. In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks. ) Caution: After performing repeat or random play, be sure to press the button. Otherwise, the disc will play continuously. () ENGLISH To clear the programmed selections: Press the CLEAR button on the remote control whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. You can choose up to 32 selections for playback in the order you like. 1 Whilst in the stop mode, press the MEMORY button to enter the programming save mode. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. ) button for less than 0. 5 seconds to se- WALK ALONG SESAME STREET ENGLISH To scan the preset stations The stations saved in memory can be scanned automatically. (Preset memory scan) 1 Press the PRESET ( or ) button for more than 0. 5 seconds. The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. 2 Press the PRESET ( or ) button again when the desired station is located. To erase entire preset memory 1 2 Press the ON/STAND-BY button to enter the stand-by mode. Whilst pressing down the REC PAUSE button and the CONTINUOUS PLAYBACK button, press the TUNER (BAND) button until "TUNER CL" appears. To change the FM/MW tuning interval: 1 Press the ON/STAND-BY button to turn the power on. 2 Press and hold down the TUNER (BAND) button, for 3 seconds. or 3 The display will appear for 2 seconds and the new setting is activated. Caution: When the unit is left for a few hours after the span has been switched and the AC power lead disconnected, the FM span will be automatically returned to 50 kHz (MW span to 9 kHz). When the span is switched, all the memorised stations will be cancelled. E-18 04/1/28 CX-GD5100V_EN2. fm Radio The International Telecommunication Union (ITU) has established that member countries should maintain either a 100 kHz or 50 kHz interval between broadcasting frequencies of FM stations and 10 kHz or 9 kHz for MW stations. The illustration shows the 50/9 kHz zones (regions 1 and 3), and the 100/10 kHz zone (region 2). This product is not equipped with a span selector. However, it will be adjusted to a 50 kHz FM (9 kHz MW) interval when shipped from the factory. Before using the unit, be sure to set it to the FM/MW tuning interval (span) used in your area. WALK ALONG SESAME STREET Listening to a cassette tape (TAPE 1 or TAPE 2) Before playback: For playback, use normal or low-noise tapes for the best sound. [. . . ] Is the unit located near excessive vibrations? Has condensation formed inside the unit? Cassette deck Symptom Cannot record. Possible cause Is the erase-prevention tab removed?Cannot record tracks with Is it a normal tape? [. . . ]