User manual HASBRO WHATZIT

[. . . ] WHATZIT DVD mikro system bestende av WHATZIT (huvudenhet), CP-DV60HF (frmre hgtalarna) och CPDV60HSW (subwoofer). Sistema DVD micro WHATZIT composto da WHATZIT (apparecchio principale), CP-DV60HF (diffusori anteriori) e CPDV60HSW (subwoofer). WHATZIT DVD micro-systeem bestaande uit WHATZIT (hoofdtoestel), CP-DV60HF (voorluidsprekers) en CP-DV60HSW (subwoofer). Microssistema DVD WHATZIT composto de WHATZIT (unidade principal), CP-DV60HF (caixas acsticas frontais) e CP-DV60HSW (subwoofer). [. . . ] Insert the plugs fully to avoid fuzzy pictures or noise. E-14 05/3/4 WHATZIT(H)_E. fm TINSZA042SJZZ WHATZIT System connections (continued) " Connecting the AC power lead After checking all the connections have been made correctly, connect the AC power lead to the AC power input socket, then plug the AC power lead of this unit into the wall socket. If you plug in the unit first, the unit will enter the demonstration mode. ENGLISH " Demonstration mode When you plug the unit in for the first time, the unit will enter the demonstration mode. To cancel the demonstration mode: When the unit is in the power standby mode (demonstration mode), press the X-BASS/DEMO button. The unit will enter the low power consumption mode. Preparation for Use Wall socket (AC 230 V, 50 Hz) Notes: !Never use a power lead other than the one supplied. Otherwise, a malfunction or an accident may occur. Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time. Cooling fan: A cooling fan is built into this unit for better heat radiation. Do not cover the opening in this section with any obstacles to avoid damage to the unit. To return to the demonstration mode: When the unit is in the power stand-by mode, press the X-BASS/ DEMO button again. Note: When the power is on, the X-BASS/DEMO button can be used to select the extra bass mode. " To turn the power on Press the ON/STAND-BY button to turn the power on. After use: Press the ON/STAND-BY button to enter the power stand-by mode. E-15 05/3/4 WHATZIT(H)_E. fm TINSZA042SJZZ Remote control " Battery installation 1 2 Remove the battery cover. Insert the supplied batteries according to the direction indicated in the battery compartment. Note: When the input source is "TUNER" or "AUX", the surround mode is not available. E-17 05/3/4 WHATZIT(H)_E. fm TINSZA042SJZZ Setting the clock 3 Within 30 seconds, press the PRESET ( or ) button to adjust the hour and then press the MEMORY/SET button. WHATZIT ENGLISH 1 2 Press the PRESET ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. 4 Within 30 seconds, press the PRESET ( or ) button to adjust the minutes and then press the MEMORY/SET button. 3 Preparation for Use 4 5 6 7 8 Press the PRESET ( or ) button once to advance the time by 1 minute. In this example, the clock is set for the 24-hour (0:00) display. To confirm the time display: Press the CLOCK button. The time display will appear for about 8 seconds. Note: The "CLOCK" or time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or unplugging the unit. To readjust the clock: Perform "Setting the clock" from step 1. If the "CLOCK" is not flashing in step 1, step 2 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on page 56 for details. ] 2 Perform "Setting the clock" from step 1. 8 1 Press the CLOCK button and within 8 seconds, press the MEMORY/SET button. 2 TINSZA042SJZZ Within 30 seconds, press the PRESET ( or ) button to select 24-hour or 12-hour display and then press the MEMORY/SET button. "0:00" "AM 12:00" The 24-hour display will appear. (0:00 - 23:59) The 12-hour display will appear. [. . . ] Is the AC power lead of the unit plugged in?Does the remote control sensor receive strong light? E-55 05/3/4 WHATZIT(H)_E. fm TINSZA042SJZZ WHATZIT " Tuner Symptom The radio makes unusual noises continuously. " Clearing all the memory (reset) Possible cause Is the unit placed near the TV or computer?Is the FM aerial or AM loop aerial placed properly?Move the aerial away from the AC power lead if it's located nearby. ENGLISH 1 2 3 4 1 2 Press the ON/STAND-BY button to enter the power stand-by mode. [. . . ]