User manual HASBRO WHEEL OF FORTUNE CROSSWORD

[. . . ] Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. [. . . ] · Before correcting the upper left of the image, pressing or returns to the reset confirmation screen. · When the position of the lower left is set, the correction is made and the display disappears. -42 H & V KEYSTONE 1 Press on the projector or on the remote control repeatedly until "H & V KEYSTONE" is displayed. · When the correction has already been made with "GEOMETRIC ADJUSTMENT", the confirmation message for resetting the correction before "H & V KEYSTONE" is displayed. On-screen Display Horizontal Keystone Correction (Adjustment with \ / |) 2 3 Press ', ", \ or | to move the position for the horizontal or vertical axes. Press tion. or to set the posi- · When "H & V KEYSTONE" is set to the values other than "0", "IMAGE RESIZING" is displayed. Basic Operation Vertical Keystone Correction (Adjustment with ' / ") -43 Image Projection IMAGE RESIZING Only when "H & V KEYSTONE" is set to the On-screen Display values other than "0", "IMAGE RESIZING" works. 1 Press on the projector or on the remote control repeatedly until "IMAGE RESIZING" is displayed. Press ', ", \ or | to correct the image distortion. Press tion. or to set the posi- 2 3 Using H & V KEYSTONE Adjustment When the Image Is Projected Diagonally 1 Press ' or " to parallelize the left and right sides of the projected image. 2 Press \ or | to parallelize the upper and lower sides of the projected image. 3 Press on the projector or on the remote control to display "IMAGE RESIZING" and then press ', ", \ or | to correct the image distortion. -44 Switching the Input Mode Select the appropriate input mode for the connected equipment. Press , , , or on the remote control to select the input mode. on the projector, the · When pressing input mode switches in order of : INPUT 1 INPUT 2 INPUT 3 on the projector, the · When pressing input mode switches between "INPUT 4" and "INPUT 5". / / / / INPUT buttons "On-screen Display of Input Mode (Example) When pressing INPUT 1/2/3 mode Using RGB * The "INPUT 3" display is an example. (When "Signal Type" is set to "D. PC RGB") . Note · When no signal is received, "NO SIGNAL" will be displayed. When non-supported signal is received, "NOT REG. " is displayed. · When "Auto Search" of the "Options (1)" menu is set to "ON", the input mode with signal can automatically be detected and displayed. (See page 78. ) · The input mode is not displayed when "OSD Display" of the "Options (1)" menu is set to "Level A" or "Level B". (See page 75. ) About the Input mode INPUT 1/ Used for projecting images from INPUT 2 equipment that sends RGB signals (RGB/ or component signals connected to component) the INPUT 1 or 2 terminals. INPUT 3 Used for projecting images (digital PC from equipment connected to RGB/digital the INPUT 3 terminal. · The break timer starts to count down as soon as ', ", \ or | is pressed. On-screen Display UNDO button Note · Pressing will cancel the break timer. · Auto Power Off function will be temporarily disabled during the break timer. When no input signal is detected for more than 15 minutes, the projector will automatically enter the standby mode if the break timer has elapsed. · The break timer will be displayed on the startup image. To change the screen displayed during the break timer, change the setting of "Startup Image" (see page 77). · When "Slave" is set for "Stack Setting", the break timer is not displayed. (See page 84. ) -50 Menu Items The following shows the items that can be set in the projector. "Picture" menu INPUT 1 / INPUT 2 / INPUT 3 Main Menu Picture Sub Menu Picture Mode Page 60 Page 60 Contrast Bright Color Tint Red Green Blue Sharp -30 -30 -30 -30 -30 -30 -30 -30 +30 +30 +30 +30 +30 +30 +30 +30 *1 *1 *1 *1 *1 *2 Standard Presentation Cinema Custom Page 60 CLR Temp *1 4500K 10500K Page 61 Pressing displays the items on the lower part of the "Picture" menu. Bright Boost 0 +10 *1 Page 61 Progressive *3 Page 62 C. M. S. Adjustment 2D Progressive 3D Progressive Film Mode Standard Custom 1 Custom 2 Custom 3 sRGB Page 64 *1 *4 DNR *5 Page 62 Reset OFF Level 1 Level 2 Level 3 Page 60 INPUT 1/INPUT 2 Signal Type INPUT 3 D. PC RGB D. PC Comp. D. Video RGB D. Video Comp. Page 63 Auto RGB Component *1 "Color", "Tint", "Red", "Green", "Blue", "CLR Temp" and "Bright Boost" cannot be adjusted when "C. Adjustment" is set to "sRGB". [. . . ] 19 Resize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 RESIZE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 RGB cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 RS-232C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]