User manual HASBRO WHY

[. . . ] 5, 6 Preparing and Using the Remote Control . . 5 Batteries for Remote Control . . . . . . . . . . . . . . . . . . . . . . . 5 Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (Refer to the figure below. ) To antenna input terminal Antenna Supplied antenna cable cable (supplied) Room antenna terminal (75-ohm type) 6 LOCATION OF USERS CONTROL Main unit (front view) Upper control panel VOL (+)/(­) CH ( )/( ) MENU TV/VIDEO MAIN POWER VOL CH MENU TV/VIDEO MAIN POWER 2 PRESET 1 Auto Preset Details are described on page 14. Speaker Speaker To change the vertical angle of the LCD TV set, tilt the screen up to 10 degrees forward or 20 degrees backward. The TV set can also be rotated 90 degrees horizontally. Please adjust the angle so that the TV set can be watched most comfortably. SLEEP indicator The SLEEP indicator lights up red when the SLEEP TIMER is set to on. Remote sensor window (The actual location is not visible. ) POWER/STANDBY indicator A green indicator lights when the power is on and a red indicator lights when in the standby mode (the indicator will not light when the main power is off). Note: I TV/VIDEO, CH ( )/( ), and VOL (+)/(­) on the main unit have the same functions as the same buttons on the remote control. Fundamentally, this operation manual provides a description based on operation with the remote control. 7 LOCATION OF USERS CONTROL (Continued) Main unit (rear view) Antenna terminal ANT. OUT AV-IN 2/ VIDEO L AUDIO R ON COMP Y ENT VIDEO AUDIO (L) AUDIO (R) Y PB PR AUDIO (L) AUDIO (R) HEADPHONE POWER INPUT (DC 12V) (LC-13B2H/LC-15B2H) AV-IN 2/OUT PB PR L AUDIO R HEAD PHONE R POW E INPUT DC12V COMPONENT AV -IN 1 VI DE O L AU DI O R SVI DE O VIDEO AUDIO (L) AUDIO (R) S-VIDEO AV-IN 1 POWER INPUT DC 13V (WHY) 8 LOCATION OF USERS CONTROL (Continued) Remote control DISPLAY Press. . . . Displays receiving channel for 10 seconds. Channel indication reduces in size after about 10 seconds. Press again. . . Removes display. POWER POWER DISPLAY SLEEP SLEEP BRIGHT MENU BRIGHT The brightness can be switched between 3 levels. MENU cursor (Upward/Downward Selection) MUTE Press. . . . Stops sound. VOL (+)/(­) VOL MENU TV/VIDEO CH CHANNEL SELECT TV/VIDEO MENU cursor (Right/Left Selection) FLASHBACK Returns to previous channel CH ( )/( ) Selects next higher channel Selects next lower channel MPX -/-- MPX Switching Audio mode. 9 BASIC OPERATION Turning on POWER Control section of main unit MAIN POWER 1 2 Press the MAIN POWER switch, located on the upper part of the main unit to ON. The Power/Standby indicator instantaneously changes from red to green and the main unit is turned on. I M ON-screen display Note: Input mode indication disappears after several seconds. Power/Standby indicator Switching TV/VIDEO AV1/AV2/COMPONENT/TV Mode 1 POWER Turn on the power of the connected video equipment. Press the TV/VIDEO and select the applicable input source. The screen displays AV1, AV2, COMPONENT or TV mode at the upper right corner each time TV/VIDEO is pressed. AV1 mode I 2 DISPLAY POWER BRIGHT SLEEP MENU TV/VIDEO TV/VIDEO VOL CH Notes: AV input mode indication remains for five seconds. · AV1: Video equipment connected to the AV1 input terminals. Search is initiated and when a TV signal is received during the search, the search stops. Repeat steps 3 and 4 above, to preset the channel positions for other broadcasts, etc. Press the MENU (PRESET-1) to return to the normal screen. UHF 471. 25MHz Manual mode screen DISPLAY SLEEP BRIGHT MENU 5 6 MENU UHF 623. 25MHz TV/VIDEO VOL(+)/(­) VOL CH CH ( () MPX -/-- Note: I SOUND SYSTEM may not have been set correctly, if noise can be heard or if there CHANNEL is no sound. SELECT In such case, reset to SOUND SYSTEM using the MENU. )/ Channel position number I In a weak reception area, or under bad reception conditions. 1 VOL CH MENU TV/VIDEO 2 PRESET 1 2 3 4 1, 2, 3, 5 Press the MENU (PRESET-1) on the upper part of the LCD TV set for more than two seconds. Press the MENU (PRESET-1) to display the MANUAL mode screen. While the MANUAL mode screen is displayed, press the MENU for more than 2 seconds. The channel position number remains in green. UHF 471. 25MHz UHF 471. 25MHz Note: I While the MANUAL mode screen is displayed, press the MENU button. (The LANGUAGE mode screen will appear. ) UHF 623. 25MHz 4 5 Adjust for good reception using the VOL (+)/(­). After finishing the adjustment, press the MENU (PRESET-1) to continue channel presetting. LANGUAGE ENGLISH SELECT: EXIT: MENU 15 PRESET (Continued) Channel Setting POWER </> DISPLAY BRIGHT 1 2 Press the MENU to display the MENU screen. Press the ]/[ to move the cursor to CH-SETTING. Press the </> to display CH-SETTING screen. (MENU screen) MENU SLEEP TIMER PICTURE FEATURE CH-SETTING SLEEP MENU MENU TV/VIDEO ]/[ VOL CH 3 4 SELECT: ENTER: EXIT: MENU MPX -/-- CHANNEL SELECT Press the ]/[ to select the desired function mode. Each time you press the </>, the setting for individual items is changed as follows: Press the MENU to return to the normal screen. (CH-SETTING screen) CH-SETTING RETURN POSITION COLOUR SYSTEM SOUND SYSTEM SKIP FINE NICAM IGR 5 6 [CH15 ] [AUTO ] [I ] [OFF ] [783. 25MHz] [ON ] [ON ] Selected item · POSITION: The channel position changes to the upper or lower number. [. . . ] · Make sure the main power switch of the main unit is on. · Make sure the BLACK LEVEL is properly adjusted. · Fluorescent lamp may have reached the end of service life. · Make sure the S-Video terminal is free of connections. [. . . ]