User manual HASBRO WONDER WORLD FAIRY DREAMS

[. . . ] Under no circumstances should the cut-off plug be inserted into a socket outlet as a serious electric shock may occur. If you are not sure how to do this, get help from a qualified electrician. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E, or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. This apparatus must be protected by a 13A fuse in the mains plug or distribution board. "WARNING: THIS APPARATUS MUST BE EARTHED" This equipment complies with the requirements of Directive 1999/5/EC. Dieses Gerät entspricht den Anforderungen der EU-Richtlinie 1999/5/EG. [. . . ] FAILURE setting is used to choose the response of the machine to incoming calls when this happens: YES (switch to FAX mode): The reception mode will switch to FAX mode, allowing the machine to continue to receive faxes automatically. With this setting, you can still use the remote commands to listen to your messages and then erase them (see Remote Operations on page 97). 91 4. Answering Machine Optional Answering Machine Settings NO (do not switch to FAX mode): The machine will answer after 19 rings, after which it will wait to receive a remote command. Most callers will hang up before it answers; however, when you call the machine from a remote location, you can wait until it answers, listen to your messages, and then erase them (see Remote Operations on page 97). If you want to change the setting to YES, press the panel keys as follows: 1 2 3 4 Press once and once. Display: A. M. SETTING Press once and twice. ON A. M. FAILURE Press . ON A. M. FAILURE 1=YES, 2=NO The display briefly shows your selection, then: Press to select YES (switch to to select NO. FAX mode), or OGM ONLY MODE 5 Press to return to the date and time display. OGM only mode If needed, you can turn off recording of incoming messages. In this case, your outgoing message will play, but callers will not be able to leave a message. (The machine will still receive faxes sent by automatic dialling. ) 1 2 92 Press once and once. Display: A. M. SETTING OGM ONLY MODE Press once and once. Transfer Function 3 4 Press . OGM ONLY MODE 1=YES, 2=NO The display briefly shows your selection, then: Press or to turn on OGM only mode, to turn it off. TOLL SAVER 5 Press to return to the date and time display. Transfer Function The Transfer function is used to have the machine automatically call you at a specified number every time it receives an incoming message. This lets you hear your messages immediately after they come in, even when you are at a remote location. To use the Transfer function, you must first program the number that you wish the machine to call (the transfer number), and record the transfer message that plays when you answer the phone at the remote location. If the machine does not answer after two rings, you can simply hang up before it answers, saving yourself the cost of that call. If you do not want to use the Toll Saver function, you can turn it off by following the steps below. In this case, the machine will answer after the number of rings set with the NUMBER OF RINGS setting (see Changing the number of rings on page 127). 1 2 3 4 Press once and once. Display: A. M. SETTING Press once. TOLL SAVER Press once. TOLL SAVER 1=YES, 2=NO The display briefly shows your selection, then: Press to turn on the Toll Saver to turn it off. function, or RECORDING TIME 5 Press to return to the date and time display. 98 Remote Operations Retrieving your messages 1 Call the machine from a tone dial telephone. When your outgoing message begins, press on the telephone. · You will hear a short beep, and the outgoing message will stop. 2 Enter your remote code number and then press . · You will hear a series of beeps equal to the number of messages recorded, or one long beep if four or more messages have been received. The machine will then play back the messages, beeping once at the end of each message. When all messages have been played back, you will hear a long beep. · If no messages have been received, you will hear a short beep. You can either hang up, or perform any of the operations described in the following section, Other remote operations. 3 While the messages are playing, you can do any of the following: · Repeat: To listen to a message a second time, press 2 and telephone before that message ends. To move back to the previous message, press message. on the 2 and during the first 3 seconds of the current · Skip forward: To skip forward to the next message, press 5 and on the telephone. · Stop: To stop playback, press 0 and on the telephone. After this, you can enter any of the commands described in the following section, Other remote operations. 99 4. Answering Machine Remote Operations · Play new messages: To listen to only your new messages, first stop playback by pressing 0 and , and then press 6 and . · Erase a message: To erase the message you are currently listening to, press 3 and before it ends. 4 When you have finished listening to your messages, you can do any of the following: · Erase all messages: Press 3 , 3 , and · Repeat playback: Press 7 and . . · Perform other operations: You can enter any of the commands described in the following section, Other remote operations. · Hang up: If you do not erase your messages first, they will be saved and any new messages will be recorded after them. [. . . ] Press . " " appears. and then 5. Press repeatedly to exit. Receiving a phone call 1. When the cordless handset rings, pick it up and press . Press and then press to listen to all your to listen to only your . [. . . ]