User manual HASBRO X-MEN PROJECT X LCD VIDEO GAME

[. . . ] If you are not sure how to do this, get help from a qualified electrician. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E, or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. This apparatus must be protected by a 13A fuse in the mains plug or distribution board. "WARNING: THIS APPARATUS MUST BE EARTHED" This equipment complies with the requirements of Directive 1999/5/EC. Dieses Gerät entspricht den Anforderungen der EU-Richtlinie 1999/5/EG. Cet appareil est conforme aux exigences de la directive 1999/5/CE. [. . . ] If you are making a phone call, lift the handset. Note: If the transmission is unsuccessful and [DOCUMENT JAMMED] appears in the display, remove the document as explained on page 67. , press to insert a pause, and then enter the number of the receiving machine. · If you are on a PBX and must dial a number to dial out, enter the number, FUNCTION press to insert a pause, and then enter the number of the receiving machine. Automatic redialling If you use auto dialling (including Direct Keypad Dialling) to send a fax and the line is busy, the machine will automatically make three redial attempts at intervals of five minutes. During this time, [RECALLING] will appear in the display, followed by the attempt number. You will not be able to dial any other locations while the message appears. 3 Check the display. If the number shown is correct, press . · If the number is not correct, press STOP to clear the incorrect digits, and then re-enter the correct digit(s). Redial You can automatically redial the last number dialled on the machine. To clear the message and stop STOP 1 Load the document(s). · If desired, press RESOLUTION/ RECEPTION MODE automatic redialling, press . to set the resolution and/or contrast. Under certain conditions, automatic redialling may stop before three redialling attempts are made. 2 Press once. Make sure the display shows the number you wish to dial. 33 3. Sending Faxes Batch Page Numbering Batch Page Numbering Use this feature to add a slash and the total number of pages to each page number on transmitted fax pages (for example, "P. This allows the recipient to check for missing pages. Sending a Fax From Memory To increase transmission speed, you can send a fax through the machine's memory. After transmission, the fax is automatically cleared from memory. Note: If a power failure occurs while sending a fax from memory, you must repeat the operation. To send a fax through memory, load the document, press , and dial using 1 Load the document(s). The pages will be retained in memory even if the power is turned off or a power failure occurs. When Secure Receive is not activated, the number of pages that can be held in memory is approximately 250. Caution: When Secure Receive is not activated, any faxes held in memory will be erased if the power is turned off or a power failure occurs. because the machine ran out of paper, be sure to add paper that is the same size as the paper previously used, or the fax print-out size will not match the size of the printing paper. If faxes held in memory are erased, a CLEAR REPORT will print when the power is restored. This provides information about the erased faxes, including the fax numbers of the transmitting machines if available. Note: If 100 pages or more are stored in memory (the display shows 40% or higher memory use when is pressed), fax and e-mail transmission may not be possible. Transmission will be possible after the faxes in memory are printed out. 37 4. Receiving Faxes If you received faxes to memory 5. Making Copies The machine can be used as a convenience copier. Sorting copies The machine is initially set to not sort copies. If you wish to have copies sorted as shown below, change the "SORT COPY" setting to YES (pp. 49 and 53). A BC 3 When you are ready to begin COPY/HELP copying, press . Originals Sorted (SORT COPY) A BC A BC Not sorted (MULTI COPY) A A B B C C Example: Two copies each of three originals If [MEMORY FULL] appears. . . [. . . ] Receiving Faxes Press RESOLUTION/ RECEPTION MODE until the desired reception mode appears in the display. 2 1 AUTO mode: The machine automatically answers and receives faxes. MANUAL mode: Answer all calls (even faxes) by picking up the handset. To begin fax reception, press . Sending a Fax by Normal Dialling 1 Lift the handset or press 2 Dial the fax number. SPEAKER . 3 Wait for the reception tone (if a person answers, ask them to press their Start key). TEL/FAX mode: The machine automatically answers and receives faxes. Voice calls are signalled by a special ringing sound. [. . . ]