User manual HASBRO ZOIDS NIGHTWISE

[. . . ] For this reason, on the MX-M350U/450U, the network expansion kit (with hard drive) must also be installed. For other functions, see the following manuals. Operation manual (for general information and copier operation): This contains safety precautions and general information such as the procedures for loading paper, removing misfeeds, and using peripheral equipment. It also provides detailed explanations of the procedures for using the copy function. [. . . ] INTERNET-FAX mode READY TO SEND. 3 Touch the [OK] key. OK You will return to the initial screen. AUTO EXPOSURE RESOLUTION AUTO ORIGINAL STANDARD FINE SUPER FINE ULTRA FINE 600x600dpi OK 200 x 100 (dpi) 200 x 200 200 x 400 HALF TONE 400 x 400 600 x 600 HALF TONE Five selections are available for the resolution. Touch the desired resolution key depending on the original to be scanned. For resolutions other than [STANDARD], the [HALF TONE] key can be selected. NOTE The initial factory resolution setting is 300x300dpi (SCAN mode) or Standard (INTERNET-FAX mode). If desired, you can change the initial setting to a different setting using the administrator setting, "Initial resolution setting" (page 8-4). SELECTING THE FILE FORMAT When you send an image to one or more recipients, the [FILE FORMAT] key enables you to temporarily override the individual file format settings (FILE TYPE / COMPRESSION MODE) stored for each recipient and send the image to all of the recipients using a single file format setting. "PDF MMR (G4)" is initially selected. NOTE This function cannot be used in Internet fax mode. Touch 1 EXPOSURE the [FILE FORMAT] key. 300x300dpi RESOLUTION PDF MMR(G4) FILE FORMAT AUTO A4 ORIGINAL "SELECT A FILE FORMAT TO APPLY IT TO ALL SCAN DESTINATIONS. " will appear in the message screen. Touch the [OK] key. 3 Touch the [OK] key. OK COMPRESSION MODE NONE You will return to the initial screen. MH (G3) (1-99) MMR PER FILE (G4) 2 Select the file type and the compression mode. READY TO SEND. RESEND OK AUTO EXPOSURE 300x300dpi RESOLUTION FILE FORMAT AUTO A4 ORIGINAL FILE TYPE PDF PROGRAMMED TIFF COMPRESSION MODE NONE MH (G3) (1-99) MMR (G4) SPECIFIED PAGES PER FILE (a) (b) (a) When the "SPECIFIED PAGES PER FILE" checkbox is not selected, all scanned pages are combined into a single file. When the checkbox is selected, one file is created per page from pages specified with. (b) Touch the or key to set the number of pages from which a file is created. NOTES The initial file format setting can be changed with the administrator setting "Initial file format setting" (page 8-5). Even if you change the settings in the FILE FORMAT setting screen, you can return to the settings stored for each recipient by selecting "PROGRAMMED" once again. The [PROGRAMMED] key returns the file type to the stored file format settings. Make sure the key and then touch the [OK] key. OK G. RAM1 The program key you touched is selected and you return to the screen of step 2. The [PROGRAM] key is highlighted. 3-3 SPECIAL MODES ERASING EDGE SHADOWS (ERASE) The erase function is used to erase the shadow lines on images produced when scanning thick originals or books. The erase modes that can be selected are shown below. The erase width is approximately 10 mm (1/2") in its initial setting. Your machine EDGE ERASE Erases shadows at edges that appear when scanning thick originals or books. The other machine Using edge erase CENTRE ERASE Transmission to other machine Combining "edge erase" with "dual page scan" on the following page Eliminates shadow lines produced by the bindings of bound documents. EDGE + CENTRE ERASE Eliminates shadow lines around the edges of images and eliminates the shadow at the centre of images. USING ERASE 1 Switch to the desired mode and touch the [SPECIAL MODES] key. ADDRESS REVIEW SPECIAL MODES ENTRY TTINGS FILE QUICK FILE If the address book screen appears, touch the [CONDITION SETTINGS] key to display the condition settings screen (page 1-13). to 4 If desired, set the width oforthe edgekey be erased (touch the key the to set the width). CENTRE 10 (0 mm 20) The erase width can be set from 0 mm (0") to 20 mm (1") in 1 mm (1/8") increments. 2 Touch the [ERASE] key. 5 Touch the outer [OK] key. AM R ERASE 2in1 CA OK You will return to the screen of step 1 and an erase icon will appear next to the [EXPOSURE] key. To cancel erase, touch the [CANCEL] key. 3 Select the desired erase mode. Select one of the three erase modes. The selected key will be highlighted. CANCEL OK ERASE EDGE ERASE CENTRE EDGE+CENTRE ERASE ERASE procedure 6 Perform the sendIMAGE". as explained in "SENDING AN For scan mode, see page 2-2. NOTE To cancel the erase function, touch the [CANCEL] key on the erase setting screen. (step 4) 3-4 SPECIAL MODES TRANSMITTING A DIVIDED ORIGINAL (DUAL PAGE SCAN) When an open book is scanned and transmitted, you can use this function to divide the two open pages of the book into two separate pages. [. . . ] Use this setting to program the e-mail address of the destination machine. Only one e-mail address can be programmed (maximum of 64 digits). Touch the [FORWARDING TO] key and input the address. the the 2 Enter64 digitse-mail address or domain name. Up to can be entered. If the first letter is not "@", the string is regarded as an e-mail address. [. . . ]