User manual HASBRO ZOIDS RED HORN

[. . . ] The key operator programs are configured by the administrator of the machine, and can only be accessed after a key operator code number has been entered. G G The key operator should change the factory default key operator code to a new code before the machine is used. To change the key operator code, follow the procedure on page 3. Contents page G KEY OPERATOR PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 G KEY OPERATOR PROGRAM LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Using the key operator programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 G DESCRIPTION OF PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Detailed menu of key operator program settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 1 KEY OPERATOR PROGRAM LIST The following list shows the key operator programs that are used to change machine settings in the display. NOTE The key operator programs that can be accessed depend on the optional equipment that is installed. G Key Operator Programs Program name ACCOUNT CONTROL AUDITING MODE ACCOUNT LIMIT PRINT PER ACCOUNT RESET ACCOUNT ACCOUNT NUMBER CONTROL NO PRINT IF ACC'T # INVALID ENERGY SAVE AUTO POWER SHUT-OFF TIMER AUTO POWER SHUT-OFF PREHEAT MODE TONER SAVE (B/W) OPERATION PANEL SETTINGS AUTO CLEAR SETTING MESSAGE DISPLAY TIME LANGUAGE SETTING DEVICE SETTINGS DISABLE DUPLEX UNIT DISABLE INVERTER UNIT DISABLE STAPLER UNIT DISABLE PAPER DESK DRAWERS DISABLE FINISHER DISABLE LARGE CAPACITY TRAY DISABLE SHIFTER UNIT SADDLE STITCH ADJUST AUTO PAPER SELECTION SETTING REGISTRATION ADJUSTMENT SECURITY SETTINGS Page 6 6 7 7 7 7 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9 9 9 11 Program name COLOUR ADJUSTMENT TEST PRINT COLOUR BALANCE EASY CALIBRATION KEY OPERATOR CODE CHANGE PRINT KEY OPERATOR PROGRAMS LIST SYSTEM SETTINGS DEFAULT SETTINGS INTERFACE SETTINGS NETWORK SETTINGS INITIALIZE/STORE SETTINGS PRODUCT KEY SERIAL NUMBER E-MAIL ALERT AND STATUS PS3 EXPANSION KIT DATA SECURITY KIT Page 14 16 18 20 20 20 21 21 22 22 22 22 22 2 KEY OPERATOR PROGRAM LIST Using the key operator programs The general procedure for using key operator programs is explained below, using "KEY OPERATOR CODE CHANGE" as an example. NOTE To use the key operator programs, you must first program a key operator code number. [. . . ] G It is recommended that colour adjustment be performed once every 500 prints. Colour adjustment functions The printer has the following two colour adjustment functions, as well as a test print for colour adjustment: Easy calibration This mode is used for fine adjustment of the grey balance at the mid density level of the colours cyan, magenta, and yellow. Use this mode to correct minor colour deviations. (see page 18) Colour Balance This function is used to adjust each of the density levels (low, mid, and high) of the four colour components, cyan, magenta, yellow and black. Use this mode when the colour deviation is significant. (see page 16) Test print This program is used to determine whether "Colour Balance" or "Easy Calibration" should be performed on the machine. (see page 14) G Colour Adjustment Flow Chart Use the Test Print on the following page to print a test page Do the colours on the test page match the colours on the standard colour chart included with the printer?(see page 15) No Yes How much do the colours differ?Large difference Small difference Using Colour Balance (see page 16) Using Easy Calibration (see page 18) Print a test page (see page 14) Colour balance is successfully adjusted 13 DESCRIPTION OF PROGRAMS Test Print This program is used to determine whether "Colour Balance" or "Easy Calibration" should be performed on the machine. (see page 13) Follow these steps to print a test page from the operation panel. 1 Display "TEST PRINT" as indicated in the chart on page 29. TEST PRINT 2 Load A4 or letter-size paper in the tray and press the [OK] key. When the [OK] key is pressed, "PRINTING. " appears in the display. After a brief interval, a colour test page will be printed (see below). [Test Page (printed by printer)] Color Balance Adjustment Level Low Density C M Y Bk C Mid Density M Y Bk High Density C M Y Bk Easy Calibration Adjustment Level Low Density Mid Density High Density The top line of the test page shows the four colours (C (cyan), M (magenta), Y (yellow), and Bk (black)) at low density, mid density, and high density. If none of the levels in column 1 match in the colour chart, do the following: G If the density level of in the colour chart is darker than the maximum value (+4) in column 1, mark "+4" in column 1. If the density level of in the colour chart is lighter than the minimum value (-4) in column 1, mark "-4" in column 1. G 3 Repeat the above step for columns 2 through 12 of the test page, comparing each column with the corresponding colour in the colour chart. 17 DESCRIPTION OF PROGRAMS Easy calibration Use Easy Calibration when there is only a small difference between the colours in the colour chart and the test page that was printed as explained on page 14. Follow the steps below to set the colour balance. 1 Display "EASY CALIBRATION" as indicated in the chart on page 29. EASY CALIBRATION 2 Press the [OK] key. TEST PAGE PRINT -OK? This message will appear. 3 Load A4 or letter-size paper in the tray and press the [OK] key. When the [OK] key is pressed, "PRINTING. " appears in the display. After a brief interval, a test page for easy calibration will be printed (see the following page). Select the colour of grey that you prefer in the test patterns (Test pattern 2 and Test pattern 3 on the following page). For a detailed explanation of this procedure, see "Easy Calibration" on the following page. Press the [ ] or [ ] key to enter the X-axis value (-3 to 3) of the preferred grey colour (this is the magenta component of the colour). 4 5 SELECTION X POSITION 0 6 7 Press the [OK] key. Press the [ ] or [ ] key to enter the Y-axis value (-3 to 3) of the preferred grey colour (this is the yellow component of the colour). SELECTION Y POSITION 0 8 Press the [OK] key. Your settings will be saved and you will return to the display of step 1. Print a test page as explained on page 14 and verify that the colours match the colours in the standard colour chart. NOTE If you cannot find an acceptable colour of grey in the test patterns, adjust the colour balance using the Colour Balance settings as explained on page 16. 18 DESCRIPTION OF PROGRAMS Easy Calibration (additional information for Steps 4 through 8 on the previous page) Easy Calibration is performed by selecting the desired colour of grey (processed grey), which is a combination of cyan, magenta, and yellow. [Test Pattern 2 (printed by printer)] Easy Calibration Testpage (1/2) [Test Pattern 3 (printed by printer)] Easy Calibration Testpage (2/2) Magenta (-3~±0) Magenta (±0~+3) Yellow (-3~+3) Example:if this is the desired colour, select "+1" for X and "-2" for Y. Yellow (-3~+3) Test patterns 2 and 3 indicate processed grey colours with the current grey colour as the reference point or origin ("0"). [. . . ] Select the low, mid, and high density values for cyan, magenta, yellow, and black. This program is explained on page 13. [] TEST PRINT [] [OK] Printing will start. This program is explained on page 13. COLOUR ADJUSTMENT [BACK/C] [] [] [OK] [OK] [OK] KEY OPERATOR CODE CHANGE [] [] [BACK/C] Enter the current code number. To enter numbers, see page 4. [BACK/C] Enter the new code number. [. . . ]