User manual HASSELBLAD FLEXBODY

[. . . ] Hasselblad A/S assumes no responsibility or liability for loss or damage incurred during or as a result of using Hasselblad software or products. Hasselblad, Imacon, FlexColor and Flextight are trademarks of Hasselblad A/S. Adobe and Adobe Photoshop are trademarks of Adobe Systems, Inc. Macintosh, Mac OS, FireWire and ColorSync are registered trademarks of Apple Computer, Inc. [. . . ] Plug the Flextight 646 power supply into a wall socket. Note that the power supply may emit a low buzzing sound when plugged in. This is normal and will not damage the power supply or scanner. Turn the scanner around so that the front is facing you. Turn on your computer and install the FlexColor image scanning software. 3. 6. User's Guide - Flextight 646 English 1. Place the scanner on a table near your computer with the front facing away from you. Make sure that the location you choose meets all environmental - and electrical requirements as described on page 11. 14 Hardware Reference - Flextight 646 Setting up the Scanner Attaching/Detaching the Feed Table English C B D A D Figure 4: Attaching/Detaching the Feed Table To attach the feed table correctly onto the scanner lead the brackets (B) as far as they go into the slits (C) in the scanner base, then lower the table and pull it slightly backwards to ensure that the notches (D) catch the bottom of the slits. To detach the feed table correctly from the scanner lift it slightly upwards to release the notches (D) from the bottom of the slits (C) then pull it away from the scanner. User's Guide - Flextight 646 Hardware Reference - Flextight 646 Setting up the Scanner 15 Mounting/Dismounting of the Cabinet A B C Figure 5: Mounting/Dismounting of the Cabinet To dismount the cabinet (A) remove the two screws (B) at the scanner back using a 2. 5 mm allen key, then pull the cabinet upwards. When mounting the cabinet, make sure that it catches the bends (C) in both sides, then lower it slowly while making sure that it goes free of all cables and extrusions and finally tighten the screws (B). User's Guide - Flextight 646 English 16 Hardware Reference - Flextight 646 Operating the Scanner English A B C FLEX TIG HT E F à OR IGIN AL HO LD ER PATE NT PE ND ING D à J K G H L M Figure 6: Operating the Flextight 646 scanner User's Guide - Flextight 646 Hardware Reference - Flextight 646 Operating the Scanner 17 Operating the Scanner (See Figure 6 opposite). It is assumed that the scanner and FlexColor software have been properly installed. Make sure that the feed table (A) has been attached properly onto the scanner (see "Attaching/Detaching the Feed Table" on page 14). · For transparency holders (H), the top layer (D) is magnetic, which will hold the original in place. · For the reflective holder (L), note the four metal pegs (the top two are shown as A and C in Figure 7 below); make sure that the clear plastic sheet is pressed all the way down over all four pegs. Note also the two curved tabs at the top of the holder (B in the figure below); the clear sheet must slip under each of these tabs, as shown. A B C Figure 7: Reflective holder, top 10. In most cases, this procedure will never be necessary. Use procedure below to make Focus Calibration: 1. Locate the "Focus sheet" that came with your scanner. It is a 8 x 9 cm (3" x 3. 5") square of transparent film with a black image on it. Focus sheet PN:40900026, rev. 1. 10 2. Load the sheet into the 6 x 6 original holder with the lines pointing towards the scanner (vertically). Place the sheet as straight as possible. Use the scanner's light table grid and the corners marked on the sheet to help align it. Select Focus Calibration from the Maintenance menu. 3. 4. [. . . ] Detach the feed table (A) as described on page 14. Remove the cabinet (B) as described on page 15. At the left side of the scanner locate the tube to be replaced and dismount the plug (C). Remove the defective tube (D): · Press the flaps backwards to release the tube. [. . . ]