User manual HAWKE 123 INDUSTRIAL GENERAL PURPOSE ASSEMBLY

[. . . ] Assembly Instructions for cable gland: 123 Industrial General Purpose Assembly Instructions AI 398 / Issue A - 08/09 Operating temperature range -60°C +100°C Certification Details Gland Type: 123 Industrial IP66 Certified to Hawke Approved Drawings Only 1 2 1. Backnut Compression Spigot Seal Middle Nut Compression Spigot Seal Entry 3 1. 1 1. 2 2. 1 2. 2 View for clarity only, do not disassemble parts , & . Cable Preparation Gland Preparation II 3 3 5mm minimum recommended II 2 2 1 2 1 Shroud Option B Unless already screwed into the equipment hold the entry in position with a spanner/ wrench to prevent rotation and tighten the middle nut using a wrench/spanner until resistance is felt between the seal and cable. [. . . ] To ease wiring inside the equipment it may be beneficial to strip the outer sheath of the cable, as shown above. IMPORTANT: Support the cable to prevent twisting. AI 398 - Issue A / Page 1 of 2 Connection Solutions Hawke International is a division of Hubbell Ltd. Registered Office: Mitre House, 160 Aldersgate Street, London EC1A 4DD. A member of the Hubbell Group of Companies Hawke International UK Office Oxford Street West, Ashton-Under-Lyne, Lancashire OL7 0NA. UK www. ehawke. com Sales: +44 (0) 161 830 6698 Technical: +44 (0) 161 830 6697 Fax: +44 (0) 161 830 6648 E-mail: sales@ehawke. com CABLE GLAND SELECTION TABLE Size Ref. Entry Thread Size Metric Os O A B C C2 D E F G H J M20 M20 M20 M25 M32 M40 M50 M63 M75 M80 M90 M100 NPT ½" ½" ½" - ¾" ¾" - 1" 1" - 1¼" 1¼" - 1½" 1½" - 2" 2" - 2½" 2½" - 3" 3½" 3½" 4" Cable Acceptance Details Outer Sheath Alternative Standard Seal (S) Seal Min. 3. 0 7. 5 11. 0 13. 0 19. 0 25. 0 31. 5 42. 5 54. 5 67. 0 67. 0 75. 0 Max. 8. 0 11. 9 14. 3 20. 2 26. 5 32. 5 42. 3/44. 4 54. 3/56. 3 65. 3/68. 2 73. 0 77. 6 91. 6 Min. ----8. 5 9. 5 15. 5 22. 0 27. 5 39. 0 48. 5 ------Max. ----13. 4 15. 4 21. 2 28. 0 34. 8 46. 5 58. 3 ------Max Length Hexagon Dimensions Across Flats 24. 0 24. 0 30. 0 36. 0 46. 0 55. 0 65. 0 80. 0 95. 0 106. 4 115. 0 127. 0 Across Corners 27. 7 27. 7 34. 6 41. 6 53. 1 63. 5 75. 1 92. 4 109. 6 123. 0 132. 8 146. 7 64 64 60 68 70 73 100 98 100 94 94 94 Sizes Os and O are available with an M16 thread size. If M16 entry is used on O size Cable Glands the maximum cable inner sheath diameter is limited to 10. 9mm. EN 50262 CABLE GLAND CLASSIFICATION Material Mechanical Properties Electrical Properties Protective Connection to Earth External Influences Resistance to Salt and Sulpher Dioxide Laden Atmospheres Sealing System Temperatire Range Ingress Protection Cable Retention (Armoured Cable) Single Orifice Seal Y Without Cable Anchorage Cable Gland Type Equipotential Bonding With Cable Anchorage Composite Metal Type Category Class Category IP66 -60° to 80° 121 Y X A 8 X Y X X X Y Y Y 1. [. . . ] Sealing washer, to offer additional ingress protection of the enclosure at the cable gland entry. Serrated washer, to dampen any vibrations that may loosen the locknut or cable gland assembly. AI 398 - Issue A / Page 2 of 2 Multi-Orifice Seal X Impact Category Connection to Metallic Layers Insulation Characteristics Non-Metallic [. . . ]