User manual HAWKE 150 DEDICATED ASSEMBLY AI 325 ISSUE K 05-06

[. . . ] Assembly Instructions for cable gland type 150/RAC Industrial General Purpose 150 Dedicated Operating temperature range -60°C +80°C 1. Backnut Reversible Armour Clamping Ring (RAC) / Dedicated Armour Clamping Ring Armour Spigot Entry (with captive deluge seal), if fitted Assembly Instructions AI 325 Issue K - 05/06 International Reversible Armour Clamping Ring (RAC) General identification ring orientation for: SWA Position Braid 'X', Flat Steel Wire 'Y', Steel Tape 'Z' Ring Position 1 2 3 4 IMPORTANT: The arrowhead indicating the correct armour thickness or type should point towards the equipment Dedicated Ring This ring will only fit in one orientation i. e. [. . . ] Note : If the equipment has a threaded entry, it may be advisable to screw the cable gland into the equipment to prevent twisting of the cable after Step D. Smarter products Hawke International is a division of Hubbell Limited A member of the Hubbell Group of Companies. AI 325 - Issue K / Page 1 of 2 International 4 5mm minimum recommended 4 3 2 4 1 1 1 D Unless already screwed into the equipment hold the entry in position with a spanner / wrench to prevent rotation. Hand tighten the backnut to the entry and turn a further 1/2 to 3/4 of a turn with a spanner / wrench. IMPORTANT: Support the cable to prevent it from twisting. To ease wiring inside the enclosure, it may be beneficial to strip the inner sheath of the cable as shown above. E Unscrew the backnut and visually inspect that the armour / braid has been successfully clamped between the armour spigot and the armour clamping ring . If armour / braid not clamped, repeat assembly. F Reassemble backnut onto the entry component . Hand tighten the backnut to the entry and turn a further 1/6 of a turn with a spanner / wrench. Locate the shroud over the cable gland, if applicable CABLE GLAND SELECTION TABLE Cable Acceptance Details Size Ref. O A B C C2 D E F Entry Thread Size Metric M20 NPT Inner Sheath Max. 11. 9 14. 3 20. 2 26. 5 32. 5 42. 3/44. 4 54. 3/56. 3 65. 3/68. 2 Steel Wire Armour/ Tape / Braid Orientation Orientation 1 2 0/0. 7 0. 9/1. 25 0. 9/1. 25 0/0. 7 1. 25/1. 6 0/0. 7 1. 6/2. 0 0/0. 7 1. 6/2. 0 0/0. 7 1. 8/2. 5 0/1. 0 1. 8/2. 5 0/1. 0 0/1. 0 1. 8/2. 5 Max Length Hexagon Dimensions Across Across Flats Corners 24. 0 27. 7 34. 6 30. 0 41. 6 36. 0 46. 0 53. 1 63. 5 55. 0 75. 1 65. 0 92. 4 80. 0 95. 0 109. 6 ½" M20 ½" - ¾" M25 ¾" - 1" M32 1" - 1¼" M40 1¼" - 1½" M50 1½" - 2" M63 2" - 2½" M75 2½" - 3" 51 51 55 60 70 76 78 80 Size O is available with an M16 thread size. If M16 entry is used on O size Cable Glands the maximum cable inner sheath diameter is limited to 10. 9mm. [. . . ] Serrated washer, to dampen any vibrations that may loosen the locknut or cable gland assembly. Visit our Web Site at www. ehawke. com AI 325 - Issue K / Page 2 of 2 Hawke International UK Office, Oxford Street West, Ashton-under-Lyne, Lancashire. Sales: UK 0870 60 60 105 Sales: +44 (0) 161 830 6698 Technical UK: 0870 458 9358 Technical: +44 (0) 161 830 6697 Fax: +44 (0) 161 830 6648 E-mail: sales@ehawke. com Safety First International [. . . ]