User manual HAWKE 153 ASSEMBLY AI 341 ISSUE K 05-06

[. . . ] Assembly Instructions for cable gland type 153 9MX2 Class 1 Zone 1 AExe II Offshore Class 1 Zone 2 AExe II Onshore See Schedule of Limitations : AExe Assembly Instructions AI 341 Issue K - 05/06 Operating temperature range -20°C +70°C Listing No. 6. Backnut Middle Nut Braid Clamping Ring Braid Spigot Inner Seal Entry (with captive deluge seal), if fitted 1 2 3 4 6 5 1a Please Note: For G, H & J size glands the part 1 will be substituted by part 1a. Cable Preparation Cable Gland Preparation 6 5 Braid 4 II I 3 2 3 2 1 4 3 2 1 1 Shroud option A Strip Cable to suit equipment as shown above and expose the braid 'I'. [. . . ] If braid not clamped, repeat assembly. F Remove entry and refit inner seal , replace entry and re-assemble middle nut onto the entry component . Tighten up the middle nut using a wrench / spanner until resistance is felt between the seal and cable, then turn the middle nut through a further half a full turn to complete the inner seal. Tighten the backnut to form a seal around the cable, then tighten a further full turn using a wrench / spanner. Ensure that the middle nut does not rotate when tightening the backnut . Ensure that the deluge seal is pulled down into position, if fitted. Locate the shroud over the cable gland, if applicable. AI 341 - Issue K / Page 2 of 4 CABLE GLAND SELECTION TABLE Size Ref. Os O A B C C2 D E F G H J Entry Thread Size Metric M20 M20 M20 M25 M32 M40 M50 M63 M75 M80 M90 M100 Cable Acceptance Details Inner Sheath'A' Outer Sheath Standard Alternative 'B' Seal Seal (S) NPT Min. ½" 0. 12" 0. 31" 0. 22" 0. 47" ½" 0. 30" 0. 46" 0. 37" 0. 63" ½" 0. 44" 0. 56" 0. 34" 0. 52" 0. 49" 0. 81" ¾" 0. 52" 0. 79" 0. 38" 0. 60" 0. 66" 1. 02" 1" 0. 75" 1. 04" 0. 61" 0. 83" 0. 87" 1. 30" 1¼" 0. 99" 1. 27" 0. 87" 1. 10" 1. 10" 1. 61" 2" 1. 24" 1. 74" 1. 09" 1. 37" 1. 42" 2. 07" 2½" 1. 68" 2. 21" 1. 54" 1. 83" 1. 81" 2. 57" 3" 2. 15" 2. 68" 1. 91" 2. 29" 2. 24" 3. 07" 3½" 2. 63" 2. 87" 3. 05" 3. 52" 3. 05" 3. 52" 3½" 2. 63" 3. 05" 4" 2. 95" 3. 60" 3. 46" 4. 11" 'C' Wire Braid 'X' 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 0. 008"/0. 013" 'G' Hexagon Dimensions Across Across Flats Corners 0. 94" 1. 09" 0. 94" 1. 09" 1. 18" 1. 36" 1. 42" 1. 64" 1. 81" 2. 09" 2. 17" 2. 50" 2. 56" 2. 96" 3. 15" 3. 64" 3. 74" 4. 31" 4. 19" 4. 84" 4. 52" 5. 22" 5. 00" 5. 77" 3. 19" 3. 19" 3. 27" 3. 43" 3. 62" 3. 90" 4. 45" 4. 61" 4. 72" 4. 48" 4. 48" 4. 48" Sizes Os and O are available with an M16 thread size. If M16 entry is used on O size Cable Glands the maximum cable inner sheath diameter is limited to 0. 43mm. SCHEDULE OF LIMITATIONS: AExe 1. The cable glands when used with braided cable types are only suitable for use with fixed aparatus, the cable for which must be effectively clamped and cleated elsewhere. This cable gland has an operating temperature range of -20°C to +70°C. When the glands are used in increased safety applications a UL Listed sealing washer may be required between the external face of the enclosure and the gland sealing face in order to maintain the integrity of the increased safety enclosure. A grounding / earth tage has been provided for use as a grounding point when the cable gland is used with plastic enclosures. This must be fitted to the wall of the enclosure using the threads of the gland and the locknut supplied. [. . . ] Serrated washer to dampen any vibrations that may loosen the locknut or cable gland assembly. AI 341 - Issue K / Page 3 of 4 Visit our Web Site at www. ehawke. com AI 341 - Issue K / Page 4 of 4 Hawke International UK Office, Oxford Street West, Ashton-under-Lyne, Lancashire. Sales: UK 0870 60 60 105 Sales: +44 (0) 161 830 6698 Technical UK: 0870 458 9358 Technical: +44 (0) 161 830 6697 Fax: +44 (0) 161 830 6648 E-mail: sales@ehawke. com Safety First International [. . . ]