User manual HAWKE 453-T EXD I-EXE I ASSEMBLY AI 381 ISSUE A 12-08
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HAWKE 453-T EXD I-EXE I. We hope that this HAWKE 453-T EXD I-EXE I user guide will be useful to you.
Lastmanuals help download the user guide HAWKE 453-T EXD I-EXE I.
Manual abstract: user guide HAWKE 453-T EXD I-EXE IASSEMBLY AI 381 ISSUE A 12-08
Detailed instructions for use are in the User's Guide.
[. . . ] Assembly Instructions for cable gland: 453/T Exd I/Exe I
Operating temperature range -60°C +80°C
International
Assembly Instructions AI 381 / Issue A - 12/08 Certification Details
Gland Type: 453/T Exd I/Exe I Baseefa08ATEX0331X IM 2 IP66 IECEx BAS08. 0112X
1 2
1. 6.
Backnut Middle Nut Armour Clamping Spigot Armour Clamping Ring Inner Seal Entry (with captive deluge seal), if fitted
3
4 5 6
Cable Preparation
Gland Preparation
6
5
II
Armour 4 4
I
3 2 1
3
3
2 2 1 1
A Strip Cable to suit equipment as shown above and expose the armour 'I' removing all cable fillers. [. . . ] UK
www. ehawke. com
AI 381 - Issue A / Page 1 of 2 Sales (UK): 0870 606 0105 Sales: +44 (0) 161 830 6698 Technical (UK): 0870 458 9358 Technical: +44 (0) 161 830 6697 Fax: +44 (0) 161 830 6648 E-mail: sales@ehawke. com
6
5mm minimum recommended
6 4 3 2 1 1 2 5
6
2 1
D Unless already screwed into the equipment hold the entry in position with a spanner/wrench to prevent rotation. Hand tighten the middle nut to the entry and turn a further half to one full turn with a spanner/wrench. IMPORTANT: Support the cable to prevent it from twisting. To ease wiring inside the enclosure, it may be beneficial to strip the inner sheath of the cable as shown above.
E Unscrew the middle nut and visually inspect that the armour has been successfully clamped between the armour clamping ring and the armour clamping spigot . If armour/braid not clamped, repeat assembly.
F Remove entry and refit inner seal , replace entry and re-assemble middle nut onto the entry component . Tighten up the middle nut using a wrench/spanner until resistance is felt between the seal and cable, then turn the middle nut through a further half a full turn to complete the inner seal. Tighten the backnut to form a seal around the cable, then tighten a further full turn using a wrench/spanner. Ensure that the middle nut does not rotate when tightening the backnut . Ensure that the deluge seal is pulled down into position, if fitted. Locate the shroud over the cable gland, if applicable.
CABLE GLAND SELECTION TABLE
Size Ref. Entry Thread Size Metric O A B C C2 D E F M20 M20 M25 M32 M40 M50 M63 M75 NPT ½" ½" - ¾" ¾" - 1" Cable Acceptance Details Inner Sheath/Cores Outer Sheath Min. 11. 9 14. 3 19. 7 26. 5 32. 5 42. 3/44. 4 54. 3/56. 3 65. 3/68. 2 Min. 9. 5 12. 5 16. 9 22. 0 28. 0 36. 0 46. 0 57. 0 Max. [. . . ] Earthtag, to provide an external armour/braid bonding point. Serrated washer, to dampen any vibrations that may loosen the locknut or cable gland assembly. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HAWKE 453-T EXD I-EXE I
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HAWKE 453-T EXD I-EXE I will begin.
