User manual HAWKE S701 ASSEMBLY AI 315 AI342 ISSUE L 11-06

[. . . ] Assembly Instructions for cable gland type 701 8N44 Wet Locations E165706 S701 8N44 Wet Locations E165706 Class 1 Zone 1 AExe II (MCHL) Class 1 Zone 2 AExe II (MC) See Schedule of Limitations : AExe 32R4 E84940 Assembly Instructions AI 315 (A - F) AI342 (H, J & K) Issue L - 11/06 Operating temperature range -50°C +60°C 1. Backnut Middle Nut Armour Grounding Device Armour Stop Entry (with captive deluge seal), if fitted International 1 2 3 4 5 1a Please Note: For H size gland the part 1 will be substituted by part 1a. Cable Preparation Cable Gland Preparation 5 5 II I 4 2 3 1 2 1 A Strip cable to suit equipment as shown above, exposing metal armour sheath (I) and insulated cores (II). [. . . ] Tighten the backnut to form a seal around the cable, then tighten a further full turn using a wrench / spanner. Ensure that the middle nut does not rotate when tightening the backnut . Ensure that the deluge seal is pulled down into position if fitted. Locate the shroud over the cable gland, if applicable AI 315 & AI 342 - Issue L / Page 2 of 4 CABLE GLAND SELECTION TABLE Size Ref. A B C C2 D E F Armour Sheath Armour Stop Min. NPT Metric Bore 0. 39" 0. 41" 0. 64" M20 ½" - ¾" ¾" - 1" 0. 48" 0. 49" 0. 93" M25 M32 1" - 1¼" 0. 83" 0. 85" 1. 23" M40 1¼" - 1½" 1. 14" 1. 17" 1. 59" 1½" - 2" M50 1. 35" 1. 37" 1. 96" M63 2" - 2½" 1. 73" 1. 76" 2. 55" M75 2½" - 3" 2. 27" 2. 29" 2. 98" Entry Thread Size Cable Acceptance Details Outer Sheath Min. 0. 49" 0. 66" 0. 87" 1. 10" 1. 42" 1. 81" 2. 24" Max. 0. 80" 1. 02" 1. 29" 1. 61" 2. 07" 2. 57" 3. 07" Hexagon Dimensions Max Length Across Across Flats Corners 3. 35" 1. 18" 1. 36" 3. 61" 1. 42" 1. 64" 3. 90" 1. 81" 2. 09" 4. 01" 2. 17" 2. 50" 4. 94" 2. 56" 2. 96" 5. 15" 3. 15" 3. 64" 5. 17" 3. 74" 4. 31" H J K ** M90 M100 --- 3½" 4" 6" 2. 90" ----- 2. 92" 3. 47" 3. 07" ** ** 3. 46" ** ** *** 3. 52" 4. 11" *** 5. 17" 5. 17" 5. 17" 4. 18" 5. 00" 6. 80" 4. 84" 5. 70" 7. 71" The armour grounding device is manufactured to suit the over armour diameter of the cable. The outer seals are manufactured to suit the O/D of the cable and have a maximum 3mm (1/8) range. Therefore, more than 1 seal may be supplied. *** Note: J & K size glands do not carry UL Wet Location listing. SCHEDULE OF LIMITATIONS: AExe 1. This cable gland has an operating temperature range of -50°C to +60°C. When the glands are used in increased safety applications a UL Listed sealing washer may be required between the external face of the enclosure and the gland sealing face in order to maintain the integrity of the increased safety enclosure. A grounding / earth tag has been provided for use as a grounding point when the cable gland is used with plastic enclosures. This must be fitted to the wall of the enclosure using the threads of the gland and the locknut supplied. [. . . ] Serrated washer, to dampen any vibrations that may loosen the locknut or cable gland assembly. AI 315 & AI 342 - Issue L / Page 3 of 4 Visit our Web Site at www. ehawke. com AI 315 & AI 342 - Issue L / Page 4 of 4 Hawke International UK Office, Oxford Street West, Ashton-under-Lyne, Lancashire. Sales: UK 0870 60 60 105 Sales: +44 (0) 161 830 6698 Technical UK: 0870 458 9358 Technical: +44 (0) 161 830 6697 Fax: +44 (0) 161 830 6648 E-mail: sales@ehawke. com Safety First International [. . . ]