User manual HAYES DISC BRAKES MX-1 INSTALL 45-15216D4
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HAYES DISC BRAKES MX-1 INSTALL 45-15216D4. We hope that this HAYES DISC BRAKES MX-1 INSTALL 45-15216D4 user guide will be useful to you.
Lastmanuals help download the user guide HAYES DISC BRAKES MX-1 INSTALL 45-15216D4.
Manual abstract: user guide HAYES DISC BRAKES MX-1 INSTALL 45-15216D4
Detailed instructions for use are in the User's Guide.
[. . . ] We recommend the use of steel, quick release skewers only. Clean the disc and the hub mounting surface with isopropyl alcohol. Warning : Do not use disc brake cleaners. [. . . ] Note: You may need to rotate the lever arm forward until there is a 015"-. 020" (. 38-. 50mm) gap. Trim the excess cable and crimp a cable end cap on the end of the trimmed cable. While holding the brake lever, shake the mechanical brake to position it in its natural centered position over the disc. While still squeezing the lever, tighten the mounting bolts. Turn the fixed pad adjuster counter clockwise 1/8 of a turn until there is a . 015 - . 020 inch (. 38-. 50 mm) gap. Adjust the amount of lever travel by turning the adjuster barrel at your lever. Note: With the MX-1 you may use the adjuster barrel on the caliper to adjust lever travel. Check that it spins freely and that the gaps, between the pad and the disc, are equal. If the gaps are unequal, or if there is drag, readjust the caliper position by loosening the mounting bolts and adjusting the caliper as needed. Hint: A white piece of paper can be used as a background to help sight down the disc looking for equal clearance between the pads and the disc. When the gaps are equal and wheel spins freely (without drag) torque the mounting bolts to 110 in-lbs (12. 43 Nm). Repeat the procedure for the other wheel.
:
Starting Out
Burnish: Disc brakes require a special burnishing period to achieve maximum braking power. This burnishing period lasts for about 30-40 stops. During this period some noise may occur.
Maintenance
A. Cleaning and Care : The brake disc and pads should only be cleaned with isopropyl alcohol (not disc brake cleaner). Brake Pad Change: Due to wear, contamination, or damage, the brake pads will, on occasion have to be replaced. [. . . ] The cost of normal maintenance or replacement of service items, which are not defective, shall be paid for by the original purchaser. This warranty is expressly in lieu of all other warranties, and any implied are limited in duration to the same duration as the expressed warranty herein. Hayes Disc Brake shall not be liable for any incidental or consequential damages. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HAYES DISC BRAKES MX-1 INSTALL 45-15216D4
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HAYES DISC BRAKES MX-1 INSTALL 45-15216D4 will begin.
