User manual HEAT AND GLO 6000CLX-IPILP-S

[. . . ] Owner's Manual Installation and Operation Models: 6000CLX-IPI-T 6000CLX-IPILP-T 6000CLX-IPI-S 6000CLX-IPILP-S 8000CLX-IPI-T 8000CLX-IPILP-T 8000CLX-IPI-S 8000CLX-IPILP-S NOTICE DO NOT DISCARD THIS MANUAL · Important operating and maintenance instructions included. · Read, understand and follow these instructions for safe installation and operation. · Leave this manual with party responsible for use and operation. D DI O N SC OT AR D WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. · DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] · Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop. · Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance. INSERT 3 SCREWS BEND 3 TABS OUTWARD TO FASTEN TO CEILING FIRESTOP-BEND REMAINING TABS INWARD 90 DEGREES TO MAINTAIN CLEARANCE BEND ALL TABS INWARD 90° TO MAINTAIN CLEARANCE AND PREVENT INSULATION FROM FALLING INSIDE Figure 8. 5 Attic Insulation Shield E. Installing the Optional Heat-Zone-Gas Kit · Remove the knockout from the fireplace and discard it (see Figure 8. 6). · Center the duct collar around the exposed hole and attach it to the fireplace with 3 screws. Note: Do this BEFORE final positioning of fireplace. · Determine the location for the air register/fan housing assembly. Reference the Heat-Zone-Gas kit instructions for the remaining installation steps. Vaulted Ceiling Installation · Remove one shield from box. NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield. · Cut the attic insulation shield (if application is for vaulted ceiling) to fit your ceiling pitch. bend tabs all the way around the bottom. · Wrap shield around pipe if pipe is already installed in area to be insulated. · Match the three holes in each side and fasten with three screws to form a tube. · Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop. · Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop. · Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance. HEAT-ZONE-GAS ATTACHES HERE Figure 8. 6 Heat Zone Cover Plate Heat & Glo · 6000CLX-IPI-S, 6000CLX-IPI-T, 8000CLX-S, 8000CLX-IPI-T · 2166-900 Rev. G · 12/09 37 9 Appliance Preparation A. Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. [. . . ] (384 mm) Term Cap Minimum Effective Length 3-1/8 in. Maximum Effective Length 4-3/4 in. (305 mm) SLP-TRAP Horizontal Termination Cap Max Effective Length Trap1 79 mm 5-1/4 in. Trap2 133 mm SLK-SNKD Snorkel Termination Cap SLP-CCS-BK Cathedral Ceiling Support Box-Black SLP-TVHW Vertical Termination Cap 26 in. 660 mm DVP-2SL Adapter DVP-HSM-B Extended Heat Shield SLP-DCF-BK Ceiling Firestop Black SLP-WT-BK Wall Thimble-Black 76 Heat & Glo · 6000CLX-IPI-S, 6000CLX-IPI-T, 8000CLX-S, 8000CLX-IPI-T · 2166-900 Rev. [. . . ]