User manual HEAT AND GLO BRAVO

[. . . ] Para obtener un ejemplar en Español de este Manual del propietario, visite www. heatnglo. com. Pour demander un exemplaire en français de ce Manuel du propriétaire, visitez www. heatnglo. com. Owner's Manual Installation and Operation Model: Bravo CAUTION DO NOT DISCARD THIS MANUAL · Important operating and maintenance instructions included. · Read, understand and follow these instructions for safe installation and operation. · Leave this manual with party responsible for use and operation. D DI O N SC OT AR D WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. · Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] Low voltage and 110 VAC voltage cannot be shared within the same wall box. CAUTION Battery polarity must be correct or module damage will occur. · · · Optional Accessories Requirements Wiring for optional accessories should be done now to avoid reconstruction. D. Wall Switch (Required) A wall switch must be installed of this fireplace. This will allow the unit to operate if the power goes out (battery operation). Position the wall switch in the desired position on the wall. An assembly of 18 ft of 20 AWG is provided with the appliance to connect the wall switch to the appliance. Instead of the supplied assembly, wire with a length of 25 ft or less and a gauge of 20 AWG through 14 AWG is acceptable. The wire needs a jacket with a temperature rating of 140oF (60oC) or higher. At the appliance connect the wire to the ON/OFF switch pigtails. Heat & Glo · Bravo · 704-902 Rev. E · 7/08 29 INTERMITTENT PILOT IGNITOR PLUG-IN 3V TRANSFORMER ON/OFF WALL SWITCH IGNITION MODULE 3 VAC FLAME SPARKER/ SENSOR IGNITION MODULE (3V) LOW VOLTAGE SEE NOTE 1. VALVE LOW VOLTAGE SEE NOTE 1 GROUND NEUTRAL REMOTE CONTROL HOT GROUND TO FIREPLACE CHASSIS WHT ORG BLK RED BRN BRN ORG WHITE WIRE CAN BE PLUGGED INTO ANY OF #1 - #5 LOCATIONS ON THE NEUTRAL SIDE BLACK WIRE CAN BE PLUGGED INTO ANY OF #1 - #5 LOCATIONS ON THE HOT SIDE TRANSFORMER 3 VAC VALVE GRN PLUG IN REMOTE JUMPER WIRE THERMOSTAT WIRE ASSEMBLY 2045-045 NOTE 1: IGNITION MODULE, VALVE, PILOT AND WALL SWITCH OPERATE ON 3 VOLTS. 120 VAC IS REQUIRED AT JUNCTION BOX UNLESS EQUIPPED WITH BATTERY BACK-UP. Figure 10. 1 Intellifire Pilot Ignition (IPI) Wiring Diagram CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. WARNING Shock hazard. · Replace damaged wire with type 105O C rated wire. · Wire must have high temperature insulation. 30 Heat & Glo · Bravo · 704-902 Rev. Junction Box Installation If the box is being wired from the OUTSIDE of the appliance: · · · Remove the cover plate located on the outer shell - right side (see Figure 10. 3). Install the supplied RomexTM connector in the cover plate. Feed the necessary length of wire through the connector. HT Romex Connector 14/2WG Cover Plate outside firebox · Make all necessary wire connections and reattach the cover plate to the outer shell. WHT B LK BLK W If the box is being wired from the INSIDE of the appliance: · Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 10. 3). Pull the electrical wires from outside the appliance through this opening into the valve compartment. GRN wire inside box Copper ground attached to GRN screw with GRN wire Note: Do NOT wire 110VAC to wall switch. Figure 10. 3 Junction Box Detail · · Feed the necessary length of wire through the connector. Make all necessary wire connections to the junction box/receptacle and assemble the junction box/receptacle to the outer shell. · Heat & Glo · Bravo · 704-902 Rev. E · 7/08 31 11 Finishing A. Mantel Projections Figure 11. 1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance. 1/2 INCH NON-COMBUSTIBLE BOARD REQUIRED ON UNIT FACE Note: All measurements in inches. 1 IN C H M IN I M U M TO V E N T P IP E 15 13 12 10 9 6 5 COMBUSTIBLE MATERIALS MAY CONTACT AND COVER FRONT AND SIDE AREAS BELOW GLASS/FRONT 31 C E IL I N G 18 17 1 6 14 9 1/8 M IN . 3 1/8 FINISHING EDGE TRIM NAILING TABS 11 7 8 3 7/8 TOP OF F IN I S H I N G S T R I P TOP OF U N IT Figure 11. 3 Noncombustible Facing Diagram Figure 11. 1 Clearances to Mantels or other Combustibles above Appliance WARNING Risk of Fire · · Non-combustible clearances MUST be maintained. [. . . ] The maximum amount recoverable under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an expedient and cost-effective manner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price of the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE PRODUCT. Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-Year Warranty. Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty unless expressly authorized and approved by HEAT & GLO in writing. [. . . ]