User manual HEAT AND GLO NORTHSTAR-NT

[. . . ] Owner's Manual Installation and Operation EPA CERTIFIED WOODBURNING FIREPLACE NORTHSTAR Model: NORTHSTAR-BK NORTHSTAR-GT NORTHSTAR-NT Tested and Listed by O-T L C US Portland Oregon USA OMNI-Test Laboratories, Inc. CAUTION DO NOT DISCARD THIS MANUAL · Important operating and maintenance instructions included. · Read, understand and follow these instructions for safe installation and operation. · Leave this manual with party responsible for use and operation. D DI O N SC O AR T D WARNING If the information in these instructions is not followed exactly, a fire may result causing property damage, personal injury, or death. · Donotstoreorusegasolineorotherflammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] Remove 2 Phillips head screws and pry open access doorinthebottomofthefireplacewithaflatheadscrewdriver. Figure 5. 2. Figure 35. 4 Pry pointed edge toward fireplace and then down and out to remove. Remove 2 screws & pry open door Cover Plate Figure 35. 5 Figure 35. 2 6. Remove 2 screws from cover plate & pull cover plate towardyou. Figures35. 3&35. 4. Useaflatheadscrewdrivertoprythecorneredgeloose. Prytowardthefireplace and then press down and out. Figure 5. 5. September 1, 2008 Heat & Glo · NorthStar EPA Fireplace · 480-1081C Page 5 7. Moveslidercontrolrodandlinkagearmtotherightand 9. There is very little room to pull the timer assembly out the out of the way. Lay frontofthefireplace. Place your hand through the access the control arm down. doorinthefloorofthefireplace. Letthetimerassembly drop down and then rotate it up through the access door. Thetimerassemblyisboltedundertheface. Usea7/16 Figures 6. Figure 6. . Linkage Arm Slider Control Rod Figure 36. 1 Figure 36. 3 Remove 2 bolts from timer assembly Slider Control Rod Timer Assembly with Gasket Linkage Arm Figure 36. 4 Figure 36. 2 REMOVE & REPLACE TIMER 1. Loosen set screw on timer, remove 2 screws and remove timer. It is very important that the D cut side of the timer shaft is facing the opposite side of the linkage timer arm. Figure 6. 6. Remove 2 screws Remove Timer Loosen Set Screw Figure 36. 5 D cut side of timer shaft must face away from the Linkage Timer Arm Figure 36. 6 Page 6 Heat & Glo · NorthStar EPA Fireplace · 480-1081C September 1, 2008 . Place linkage control arm over timer shaft and tighten set screw. Rotate linkage control arm into final position and reattach to mounting plate. Note that the D cut is now facing the linkage timer arm. Figure 7. 2. Attach to Mounting Plate Tighten set screw "D" cut is not facing the Linkage Arm Figure 37. 1 Figure 37. 2 Attach Linkage Timer Arm Figure 37. 3 Exploded View of Entire Assembly for Point of Reference only Item 1 2 4 5 Description Screw8-32x1/2PHPHLTC Screw6-32x1/4PHPHLTC Washer SAE #10 Bushing Linkage Control Arm Qty 2 2 2 2 1 Item 6 7 8 9 10 Description Attachment Nut & Set Screw Linkage Timer Arm Door Linkage Timer, Mechanical, 12hours MountingBracket Qty 1 1 1 1 1 September 1, 2008 Heat & Glo · NorthStar EPA Fireplace · 480-1081C Page 7 8 Finishing A. Hearth Extension whereas you can not do this for k value. The HIGHER the R A hearth extension must be installed with all fireplaces to factor means less heat is being conducted through the nonprotect the combustible floor in front of the fireplace from combustible material to the combustible material beneath it. See Figures 8. 1 below, and The R value of a material must be equal or larger then the required R value to be acceptable. Converting k to R: High temperature (300°F min. ) continuous, non-combustible sealant Tile, stone or other non-combustible material Divide 1 by k and multiply the results times the thickness in inches of the material. Fireplace HX3 or HX4 Hearth Ext or equivalent insulation (see Table below) Protective Metal Hearth Strip R=1/kxinchesofthickness Converting R to k: Divide the inches of thickness by R. k=inchesofthickness/R Calculations: Example:Floorprotectionrequireskvalueof0. 84and3/4inch thick. [. . . ] Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts. Warranty Period Parts Labor HHTManufacturedAppliancesandVenting EPA Wood Pellet Electric Wood X X X X Components Covered AllPartsandMaterialExcept as covered by Conditions, Exclusion, and Limitations listed Igniters, Electronic Components, and Glass Blowers MoldedRefractoryPanels X X X X X X X X X X X 9-01-08 X X X Firepots Castings&Baffles Firebox, HHT Chimney, Termination & Heat Exchanger Burners, Logs & Refractory Gas Venting 1 Year X X X 2 years X X X years 5 years 7 years 10 years Limited Lifetime years years 1 year 1 year X X X Firebox & Heat Exchanger All Replacement Parts 90 Days See Conditions, Exclusions, and limitations. CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its original place of installation. The maximum amount recoverable under this warranty is limited to the purchase price of the product. [. . . ]