User manual HERCULES DJCONTROL INSTINCT REFERENCE GUIDE

[. . . ] For Windows 98 / 98 SE / Millennium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . For Windows 2000 / XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting and disconnecting the DJ Console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PRESENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connecting speakers in 5. 1 mode - Make sure that your computer is switched off. - Connect the front speakers to the 1 and 2 RCA plugs (plug 1 corresponds to the front left speaker, plug 2 to the front right speaker) or to the Front 1-2 minijack plug. - Connect the center speaker to the 3 RCA plug and the subwoofer to the 4 RCA plug, or connect the center speaker/subwoofer pair to the Center/LFE 3-4 minijack plug. - Connect the rear speakers to the 5 and 6 RCA plugs (plug 5 corresponds to the rear left speaker, plug 6 to the rear right speaker) or to the Rear 5-6 minijack plug. - Switch on your computer and your speakers. - Click on the 5. 1 / DJ / ASIO switch to enable 5. 1 mode. Your setup is now ready to reproduce surround sound. 5. 2. Connecting speakers in DJ mode - Make sure that your computer is switched off. - Connect the speakers to the 1 and 2 RCA plugs (plug 1 corresponds to the front left speaker, plug 2 to the front right speaker) or to the Front 1-2 minijack plug. - Connect your headphones to the headphone plug on the front face. - Switch on your computer and your speakers. To do this, simply press the Master tempo button. The red LED then indicates that the Pitch slider now controls the tempo, and not the pitch. Note: the functions of controls may vary according to the application you are using. 6. 4. Creating loops and cue points Finished synchronizing the tempos of your pieces?Great ­ but depending on the pieces you are using, you may wish to start up playback at a specific point and not simply at the beginning. This is possible by inserting cue points in your pieces. A cue point is a marker, directly accessible by pressing a button (the 1, 2 and 3 buttons when the Cue LED is lit up). You must first use the CUE button to set the cue points, which will allow you to define the beginning of an interesting rhythm section, for example, and start playing back the piece at that spot. Using this same marker principle you can also create loops, which are sections of a piece repeated to infinity. To do this, make sure that the Loop LED is lit up. Note: the functions of controls may vary according to the application you are using. 10/14 ­ User Manual 6. 5. [. . . ] - Consult the dealer or an experienced radio/TV technician for help. Declaration of conformity Copyright © Guillemot Corporation S. A. This publication may not be reproduced in whole or in part, summarized, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, photocopying, recording, manual or otherwise, without the prior written permission of Guillemot Corporation S. A. reserves the right to make changes to specifications at any time and without notice. The information provided by this document is believed to be accurate and reliable. [. . . ]