User manual HILTI DS KC-14

[. . . ] DS KC62-12/14 DS KC80-12/14 Operating instructions Mode d'emploi Manual de instrucciones en fr es 282236 *282236* 1 1 2 3 4 5 18 17 16 6 7 8 15 14 13 12 11 10 9 19 20 27 26 25 24 21 22 / 23 2 5 1/9 647 3 10 2 3 3 5/7 180° 4 2 10 9 1 9/10 8 4 1 4 5 6 2 7 5 8 3/4 10 1 3/4 9 6 2 1 4 5/11 3/13 9/10 8 6 7 7 9 1/13/14 6/12 3/4/5 2 7/11 8 9 10 8 10 1/13 2/11 3 1/13 5 8 6 5 - 7x 1/13 1/13 4 7 11 12 1/11/12 2/10 3 2/4 1/5 0. 5 mm (0. 02") 5/6 4/8 3/9 13 1/3 2 14 1 6/11 5/12 4/10/14 3 9 13 2/15 8 7/8 15 H T L DS KC62-12/14 and DS KC80-12/14 cut-off saws It is essential that the operating instructions are read before the machine is operated for the first time. Always keep these operating instructions together with the machine. Ensure that the operating instructions are with the machine when it is given to other persons. 1. General information 1. 1 Safety notices and their meaning -WARNINGDraws attention to a potentially dangerous situation that could lead to serious personal injury or fatality. [. . . ] Bring the grip to a comfortable personal working height. Set the depth of cut stop to the desired position by slackening the lever. (Make sure the guard will not touch the floor on reaching the full depth of cut. ) 7. Push the choke lever back to the initial position. Repeat this procedure, with the choke lever pushed in, until the engine starts. As soon as the engine starts, briefly press the throttle trigger. This will release the half-throttle lock and the engine will then run in the idling position. With the throttle in the idling position, the cutting disc must not rotate. -CAUTION 7. 1 Starting the engine -WARNING Keep other persons at least 50 ft (15 m) away from your workplace. Pay special attention to the working area to your rear. The CO in the exhaust can cause suffocation. -CAUTION The cutting disc must come to a complete stop when the motor is idling. The idling speed must be readjusted (reduced) if necessary. If this is not possible or does not bring the desired result, the saw must be sent in for repair. Check that the On /Off switch functions properly. If the throttle trigger jams, switch the machine off immediately by way of the On /Off switch. After fitting a cutting disc, check that the disc is free to rotate. After fitting a new cutting disc, the machine must be allowed to run without load at full speed for approx. Move the On /Off switch to the "On" position. Press the throttle safety grip, keep it pressed and then press the throttle trigger. Hold these two controls in this position. Use the half-throttle lock to lock the throttle trigger in the half-throttle position and then release the safety throttle grip and the throttle trigger. [. . . ] Hilti also warrants to the initial purchaser and each subsequent purchaser that the emission-related warranted parts are free from defects in material and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. These warranty periods will begin on the date small non-road equipment engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by Hilti at no cost to the owner. Hilti shall remedy warranty defects at authorized Hilti service and repair centers. [. . . ]