User manual HILTI DX76

[. . . ] DX 76 Bedienungsanleitung Operating instructions Upute za uporabu Instrukcja obslugi Návod na obsluhu Navodila za uporabo Návod k obsluze Használati utasítás de en bg hr pl ru sk sl cs hu 282470 *282470* 1 3 17 16 18 4 5 6 7 8 9 1 432 6 DX 7 2 MX 76 15 1 14 13 12 11 10 19 21 22 20 1 432 6 DX 7 2 1 3 1 4321 DX 76 4321 DX 76 4 MX 76 3 5 MX 76 3 1 432 DX 76 2 4321 DX 76 MX 76 1 432 MX 76 6 DX 7 1 max. min. 2 7 max. min. 1/4 6 DX 76 1 1 3 2 2 MX 76 MX 76 MX 76 8 9 3 1 1 432 1 MX 76 DX 76 2 4 MX 76 MX 76 2 4 4321 5 MX 76 DX 76 10 X-ENP Base material thickness (mm) Standard steel High-strength steel 20 4 red 4 black 15 3 10 blue 3 4 3 6 S 235, S275 E 36, ST 37, 340-470 N/mm2 S 355, S275 E 42, ST 52, 490-630 N/mm2 11 12 2 1 1 3 2 DX 76 13 4321 14 1 3 1 DX 76 4 2 3 2 5 4 6 red 8 4 3 15 16 34 2 5 1 3 4 1 2 17 a) max. min. h b) h max. min. c) h h h d) 18 MX 76 19 4 1 2 3 5 1 432 DX 76 7 4321 5 6 21 MX 76 DX 76 4321 DX 76 20 9 43 21 DX 76 10 11 12 14 8 DX 76 4321 4321 DX 76 13 DX 76 powder-actuated fastening tool It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. [. . . ] Insert the fastener in the tool from above. Guide the tool nosepiece into the shear connector and press the tool against the working surface at right angles. Drive the second fastener by pulling the trigger. Prepare the tool for driving the next fastener by pushing the cycling grip back toward the rear of the tool and then forward to its original position. en 25 7. 7 Fastening gratings (accessories required) 7. 7. 1 Inserting the fastener in the single-fastener tool 1. Turn the tool so that the fastener guide is pointing upwards. Insert the fastener in the tool from above. 7. 8 Fastening profile metal sheets to concrete (accessories required) 7. 8. 1 Inserting the fastener in the single-fastener tool 1. Turn the tool so that the fastener guide is pointing upwards. Insert the fastener in the tool from above. Push the cartridge strip, as far as it will go, into the cartridge strip guideway on the side of the tool. 7. 8. 3 Driving the fastener with the single-fastener tool 1. Use the stepped drill bit to predrill a hole through the profile metal sheet and into the concrete. Guide the tip of the fastener (projects from the fastener guide) into the hole drilled and press the tool against the working surface at right angles. Drive the fastener by pulling the trigger. Prepare the tool for driving the next fastener by pushing the cycling grip back toward the rear of the tool and then forward to its original position. -WARNINGDo not attempt to redrive a fastener. Do not exceed the recommended maximum fastener driving rate. 7. 8. 4 Power regulation Adjust fastener driving power by turning the power regulation wheel on the tool. Setting 1 = minimum Setting 4 = maximum 1. If a fastener is not driven deeply enough, driving power must be increased. Adjust the power regulation wheel to the next higher setting. If a fastener is driven too deeply, driving power must be decreased. Adjust the power regulation wheel to the next lower setting. [. . . ] Please ask your Hilti customer service department or Hilti sales representative for further information. Should you wish to return the tool yourself to a disposal facility for recycling, proceed as follows: Dismantle the tool as far as possible without the need for special tools. National and international directives and regulations must be observed. Separate the individual parts as follows: Part/assembly Toolbox Outer casing Piston Piston stopper Screws, small parts Used/partly-used cartridge strips Main material Plastic Plastic/synthetic rubber Steel Steel/plastic Steel Steel/plastic Recycling Plastics recycling Plastics recycling Scrap metal Scrap metal Scrap metal In accordance with local regulations 30 11. [. . . ]